Home

When you think of plumbing, do you just see it as a hidden and mysterious network of pipes and pumps that makes your toilets and sinks work? If so, then you are very unlikely to have a go at mauntaining or repairing the system. Plumbing is not actually that complicated, and there are many things that you can do yourself to maintain and repair your system. Read on to find out how.

Plumbing Repair Estimates

On very cold winter nights, allow your faucets to trickle slightly, especially if your pipes are located in a crawlspace. The running water prevents the pipes from freezing as quickly as they would otherwise. You can catch the water and use it for other household needs to prevent wasting it.

Check how well your toilets are flushing. If the handle needs to be played with in order to keep the water from running constantly, or if it needs to be held down several times in order to flush, you may need to switch out some of the parts in your tank. This is not expensive, and it could help reduce your monthly water bill. It could also mean that you avoid the embarrassment of the flushing system breaking when you have visitors!

Plumber Service Charge

Find a better way to discard of cooking oil instead of pouring it down the drain where it can easily clog your pipes. Keep a coffee can or other metal container handy to pour grease into after cooking. Place the can in the freezer to harden the grease and when it’s full, discard it with the trash.

Use strainers in all drains to catch hair and other objects. This will prevent all the material from going down the drain and causing a clog, which can cause a bigger problem down the line. Clean out the strainers daily so that you don’t start getting backup of water in your sink or tub.

Plumber Near Me Cheap

Make sure that you disconnect all hoses outside your house when the fall season hits. This is important to reduce the chance of freezing, which can cause damage to the connecting pipes. Disconnect all of your water hoses and store them safely to put your family in the best position for the fall.

If your drain in any device is taking longer to drain water, then you may need to have your pipes professionally cleaned depending on the severity of the circumstances. Before you do this, there are several different products you can try. However, some of them are professional strength and all products should be used with caution.

Make sure you get a good recommendation or check the references before you hire a plumber. With good recommendations, it will assure that you are hiring an experienced plumber. If the experienced plumber is professional, he will have a fully stocked truck and be able to complete most small jobs in one visit.

Toilet Plumbing Problems

If you live in an area that sees routine freezing temperatures, make sure you do something to keep your pipes from becoming frozen as well. There are a wide variety of ways you can keep your pipes from freezing, which will help you avoid damage to your home and costly repairs.

Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there’s a place to recycle it near your home.

If the hot water heater in your house is over ten years old, you should look at replacing it. Hot water heaters are very susceptible to corrosion on the bottom. This can lead to leaking and flooding whatever room it is in. Then not only will you have to replace it, but you’ll have to fix any damage caused by the leak.

When you’re going away on a vacation, you should consider shutting off the water supply to your home. This can help stop many problems before they start. If you don’t do this, you should have someone stop by your house regularly to check that nothing has gone wrong and that your home isn’t flooded.

Sewer Drain Cleaning Service

Realize that branch lines can get blocked and cause sewage backups that affect main lines. If you can’t clear the blockage yourself, contact a professional plumber, who can insert a snake into the line to break up the blockage.

Do not pour grease and oil down your drains. Cooking grease will build up in your pipes and could cause back-ups. Keep grease and oil in a container in your fridge and throw it in the trash when it is full. Avoid clogging your pipes with any products containing oil or grease.

If you are seeing areas in your ceiling or walls that appear to have water damage or are sagging, make sure you turn off the power before inspecting. Electricity and water do not mix. The last thing you need is to go into the attic and get shocked by a pool of water.

To avoid plumbing disasters in your kitchen, never place hard-to-grind, stringy, fibrous waste, such as poultry skins, banana peels, carrots, celery, or cantaloupe pulp, into the garbage disposer. The disposer can’t sufficiently grind these food products and they will clog your sink drain. You should also run cold water down the drain for about 15 seconds before and after using the garbage disposer to flush the waste down the main drain.

Plumbing Pipe Repair

When it comes to plumbing a great choice is to invest in brass fittings. Sure, they may be more expensive upfront, however their longevity is amazing compared to the alternatives, so you end up saving money. As an added bonus, the brass fittings look so much better than the other alternatives.

It should not be necessary to call out a professional for every repair job. If you take your time and apply sensible advice, such as what you read here, you can successfully repair many of the common faults that develop. It may take a longer the first few times, but after a few successes you will pick up speed.

Tips And Tricks On Doing Your Own Plumbing

Kitchen Sink Plumbing Repair - Hi guys, welcome to thisplumberparts. Co. Uk video, today we're looking atthe exciting installation of a shower tray. So watch the video. Remember to subscribe,remember to follow us on Facebook and Twitter, andalso remember to hold tight. See you soon. - [Announcer] Plumerparts. Co. Uk, Home of Find Your Plumber. - Right then guys so, oh, have I got anything in my hair? Don't worry, sorry about that. I'm gonna look like anidiot in this video. Anyway right, so what we'vegot is our shower tray is just going up here somewhere. And I'm pretty sure Ihave preliminary measured out already, and as islife, the shower tray weights outlet is 100%gone over the top of joist. It's probably goingover where some of those pipes are already, soit's one of those things. So without going into too much detail, I'm just gonna do this job and you guys can just follow us in the background. We're gonna get to a stage route. We're not gonna go into this box here that we fitted a few days ago. We're not gonna go into that. We just need to get ourengine half-pipe down into this area here, okay? We can't put a box in right up there because we cannot physically drill through those two joists, becausethey're so close together. We can't get a drill inthat way or that way. It's just bloody nightmare. So what we're gonna dois we're gonna run along our weights pipe, our inchand a half across down here, and then we're gonna drop it down so it's inside this cupboard. So eventually, in this area here, this is all gonna be cupboarded in, it's gonna have an unvented cylinder in here,which we're gonna fit as well. I'm sure you'll be alongfor the ride on that one. So yeah, that is what we're gonna do. You're just gonna watch, sitthere with your cup of tea, in the bliss of your bed and watch us struggle away on a Saturday morning, Saturday bloody weekend warrior, and get this done. Enjoy. So you guys, this area herehas been precisely laid out for this shower. Basically the guys who've come in here and they've boxed this bit in. So effectively, all wegot to do is we've got to lay the shower drain down in here now, and we're gonna draw a circlewith the shower tray hole where the trap goes out, and guess what? That means that's wherethe bloody shower tray outlet is gonna be, isn't it? So we got to get the shower in now, which Mark, who's off-shore at the moment, has very kindly bought Ithink the world's heaviest shower tray, but it doesn'tmatter because I'm doing the tubes this morning, so you know. So I'm gonna get it now. Where is the bloody thing? So we're gonna cut up our big stuff open. Now this is one of them moments in life you wish you brought someof those window suckers, 'cause whatever happens,you might cut yourself on this stuff, so be careful. Don't do what I'm doingand do this without gloves. How exactly did they do this Mark? - [Mark] Flatten 'em. - Okay, put it down a little bit. Standard shower trap. It'll usually come with a little tool, because once you got your part work and everything underneath,the work you're gonna do is gonna be from above. So the little tool iseffectively used to cram into one of these little slots here. You can imagine my handis the shower tray, it'll scoop down into that like that, then underneath you'vegot your rubber seal, just under here, that will be going up the underside of my hand, so therefore the underside of the shower tray, and then all that gets pulledup, together like that, to make a water-tight seal underneath. Take the decorative coveroff, the facial cover. The bit you'll put inonce this is all tiled, once these have got windows and doors, and everything else is done. So we've got our hole here. Now this is exactly whereour shower tray is gonna be, we've got a lovely little, perfect little gap just around here. So we now can draw out my hole, exactly in the place where I want it. So now we can lift up the shower tray. I'm just gonna pop itup there, outta the way out the corner, then we canlay our actual trap down, get our template ready for the trap. You can cut a hole out here for the trap, then cut a notch out,like this, to take this in a little bit, becausethis knuckle can sort of tackle the other side of the floor, and if this has been pushed out of light in anyway whatsoever, later on in the job and we come to tighten up, you won't get a water-tight seal, andyou'll have the amp. Alright, so do things like that to make it easier for you now. ♫ Oh a frown with golden brown (Graham hums) Make sure you store yourbeloved shower tray, and you're gonna put itsomewhere where it doesn't crack you around the head later on. Typically, it's a touch bit too small. Such is life, give us the old grunt work, where we gotta be. Well ain't that just typical. What we're gonna do,I'm gonna set up this, that does that, okay? So we go down, we look over the top, and we go, "Right, I'mgonna cut this bit. " That's where we're gonna run. Don't leave yourself anywhere where this can get sort of inhibitedor anything like that. Or bugger about it. At the same time, asyou can see down here, we've got joist. Now this is where coordinationbetween the trades on a job like this or any extension or any kind of new build sort of stuff. When the architects andstuff design these bases or build a control. Say you've got to havejoist in certain positions, there is times where this happens. I mean it actually happens more often than it doesn't, if you know what I mean. It's quite a common problem. So what we have to do is we coordinate with chippies or builders,and say, "Look guys, "I've got to take this joist out. "They don't want the showerto be another way around. "If we put the wasteironing on the corner, "I might not get the job that I need "to get over to the stack. " So there's a lot of thingsthat you have to think about when you're doing this sort of thing. What we'll do is I'll nowgo ahead, put my weights in, and then on Monday, whenthe chippies have got off their asses, becauseI never work weekends, they will come in andbasically sort this out. They'll have to strengthen it. Then what'll happen is we'llget building control around, they'll have a look at itand sign it off, basically. So that's value. So I want you to feelwhat we were thinking, so when you get to pullthis out, you've got to go down the ole drill. Alright, let's just get downthere and split this out. We are just gonna notch out a little bit, this little rung that we'vekind of knotted out here. Before we do anything with a shower tray, before we lock that downor anything like that, I want to make sure that this can sit in there freely and move about. So it's got like a goodfive to 10 mil around it. Any problems with the showertray later in the job, we're making it now easierfor us in the future. So you can't deny, Imean a lot of plumbing is just prep work, really. So look at that lovely bitof wood butchery there. But the main thing is nowis we can sit this in here, and it's completely flush with the bottom of the floor, so in aminute when we've got our shower tray here,and look at what movement has got as well. It's not tied up or anything like that. That means we can do allour work now from above without having to worry. We can even tighten up, you know the bit of the job that peoplehate, when you tighten up the shower trap? You know, you're not nextto it, anything like that. You can even do that now from above without having to worry too much. So a couple of tips forthis bit, number one: Every shower tray that'sever made, to be honest, this one here. Okay Mark is due, he boughta good quality one here. A lot of the time you get under here, this is just like rippled up and horrible, and yeah, difficult to seal up. Now I know that we obviouslygot our rubber seal. This is gonna go onunderneath just like this, and that is where our mainseal is gonna come from. To be honest, look at this. I'm so happy with it. Sometimes what I do is I run a little bit of gunk around here just to be sure. I felt good here anyway. I always do, it's justone of those things. Now every brand new showertray that's ever been made, they always have this littleprotective film on it. Don't pull off the whole film, okay? Leave the film overit, as long as you can, but for the bit aroundwhere we're gonna be doing our seal now, you'regonna wanna pull that film away just there. What I mean by that is just rip here. Ready for us. Just gonna put a littlebit of CT1 on here. Just leave it like that. What they would say is begood to the next person who's coming along, and ifyou got any CT1 spittering out the side or anythinglike that, just make sure you smooth that off now. Otherwise someone might comealong again to do some work here and they won't be ableto take the whole trap off, and that wouldn't be very nice, would it? Alright, so we pop our trap on here, making sure that allour other bits and bobs are outta the way. Put it in that direction. Here's the little toolthat I was talking about. Usually you just get thisin here and get this on. Well that is not gonna leak. We are literally nowjust a matter of getting yourself a sheet, clean off as much dust and snot like that from underneath. Brush as well. Brush up wherever you put the shower. Try to make sure thisis as clean as possible. This is totally fat, this shower tray, weighs an absolute tonne. If you just laid it on the floor and tried to kick the bloody thing,it wouldn't move anywhere. So what we're gonnado, we're gonna use our clear CT1 to actually gluethis down, stick it down. We'll also run a beakeraround the outside as well. After that, once that isset, literally the floor will come up with the shower tray. That stuff, it grabs on anything. So I'm just gonna quicklyclear this part up, give us a wipe down,then we're just gonna. We're gonna do it in blobs, I think blobs don't really work too well. You do these little blob points here. I just want a ring aroundthere, ring around there, ring around there, allthose little rings there and just try and run a fewup these lines here as well. It will not move anywhere, this stuff. Obviously I've cut myself a larger hole so we're not doing it as well. Important thing is here that you clean down the bottom of the shower tray. We know that there's not gonna be any dust or anything like that. Can stop this adhesive doing it's job. Even though this stuff isjust different level, really. What happens now is you basicallymove this round in a very little to attempt to get anyCT onto yourself as well. Never easy this bit, I'm afraid. And literally, that should just lay the exact way I wantit, without any problems whatsoever, look at that. We can just pop this in here now. Right, what I do now, just peel up. Remember guys, just the edges. Right then, so that'sthe shower tray down. What we need to do now is go downstairs, plant our pipe root an inch and a half, then actually get ourinch and a half installed. Right then guys, so we'vegot our 45 bit on here, so we know we can get a nice straight run, so I'm just gonna pop thisbit on now underneath. Get that as nice and tight as possible. Now obviously the problem we've got here is that we've got pretty three of joist to go through until we'reinside our cupboard area, where we can drop ourpipe down safely inside that cupboard, out of sight. Obviously you want to tryto put one bit of pipe in. Sometimes that's just notgonna happen, alright. We're gonna have quitea high hole height here, and without ripping the floor up, this all will be glued down andscrewed down already. The only way we're gonna be able to get this through at themoment is to literally, it's annoying, reallyannoying, is to basically grab a couple of couplingsand just basically glue up a few bits. So what I firstly recommendis when you're measuring your holes, just measure everything from your bottom joist, because you know these are all level, and makesure that every joist you go in on, just giveyourself another two mil. Drop yourself another twomil down, or if you want to do a little bit more, another five mil, it's totally up to you. Just make sure you geta nice, adequate draw. Going away. You're doing quite along run, then obviously you don't want to do toomany mils every joist, otherwise you're gonna endup popping out the ceiling. This is quite short aroundhere, so I can probably get away with giving myselfpretty much five mil drop on every one of these joisthere, and that work fine. Similarly, if this wasrunning the other way, what I'd do is I'd take my waste back to the side joist, sowe were going long here, and I'd clip it all theway along the joist, okay? And then when you put your clips in, you measure your clips down five mil every time to make sure youget an adequate drop on that. So I'm going to get these measured up now, I'm gonna get 'em drilled,and then we're gonna go through the rigamarole ofgetting this pipe put in. Well what I'm doing,I'm leaving this pipe, coming out of the wall,quite far off the wall because this one needs to be boarded out in here anyway, so this will leave the lads a little bitof room, so I can get in there with there. Under there where there'stroughs or whatever. Well there we go, all in. I'm really, really happy with the result. I mean it wasn't easygetting through those bits, and I hope you'llunderstand why we've done certain parts of this job. I just want to get acrossto people that everything is completely differentwhen it comes to these jobs. There's no right or wrongway of doing things. Sometimes it's just the onlyway, if you know what I mean. Right then guys, so there you go. Shower tray's laid down,we've got the weights downstairs all in. We're now ready for the other trays to come in and do theirstuff and it's the blissful world of a plumber knowingthat everything's done and that you don't have to worry anymore for another month. Anyway I hope you enjoyed the video, guys. Remember to pop over toour Facebook and Twitter, follow us there. There's links comingup now to buy T-shirts. The same T-shirt as whatI'm wearing right now. And all sorts of linksto some other videos. Anyway, I hope you have a great time, and I'll see you soon guys. Hold tight!.

Plumbing Problems Getting You Down? Read This!

Sewer Drain Cleaning Service Plumbing problems? You're not alone. Despite how simple it is to solve most plumbing problems, many people do not know how to fix their own simple plumbing issues. If you're one of these people and would like to avoid paying for the service, read on to find out how to become a plumbing expert! Solder with safety in mind. When you solder a copper pipe you want to direct the flame on the copper pipe. The flame of the torch has to be four inches away from the piping. The flame should be targeted directly at the point where the copper piping needs to be disconnected. Group all of your plumbing repairs before scheduling a plumber to come out. Check all of your fixtures and faucets. If anything is dripping, running or clogged, make a list for the plumber. That way, when the plumber comes, they can do all of the jobs in one visit. This will cut down on charges. Make sure that you disconnect all hoses outside your house when the fall season hits. This is important to reduce the chance of freezing, which can cause damage to the connecting pipes. Disconnect all of your water hoses and store them safely to put your family in the best position for the fall. Drain the sediment from the bottom of your hot water heater twice a year to keep the hot water heater working at its optimal levels. Simply open the drain valve and allow the water to run out into a bucket until the water runs clear. Then close the drain valve. Always keep your garbage disposal clean. You can do this in many ways. Pour some dish soap in and let the disposal run for a few minutes with some cold water. Be sure to run it regularly, if not, it can cause rust. To eliminate foul odors, grind lemon or other citrus peels. You can clean the walls of the disposal by grinding small fruit pits or egg shells. One way to prevent pipes from freezing during the winter is to keep cabinet doors in your house that contain the pipes open. This can insure that they get adequate heat to keep warm. Make sure also, to unhook and kind of hose outside and run a little water to clear the pipes of any remaining water going outside. If you have drains in your house that have not been used for a long period of time, pour one gallon of water through them to keep them functional. Furthermore, this will have the added benefit of reducing any odors from entering your house from lack of use during the year. Try to limit the amount of hair that goes down your drains. Hair can become tangled up in the pipe and end up blocking up the them, preventing water from flowing smoothly. Buy a cheap screened drain cover to put over your drain to stop any hair from going down and clean it off regularly. Work with plumbers that offer flat rates. When a plumber is charging by the hour, they do not have an incentive to get the job done quickly. It is human nature to go just a little bit slower if it'll mean extra money in our pockets. If you cannot find someone who charges per project make sure that you are vigilant in watching the clock and their work. Teach kids how to shut off the toilet's water supply. Kids are notorious for putting large wads of toilet paper and other things into the toilet, which inevitably leads to the toilet overflowing. Especially if your bathroom has carpet, show kids how to turn the water valve off if the toilet water keeps rising, to prevent the mess of an overflow. When searching for a good plumber you should always check references. It is easy to just go with the lowest price, but you have to do your research and make sure the plumber has a good reputation with the people they have done work for in the past so you do not get a bad plumber. Use a product like BioBen if you are planning to leave your system shut off for a few weeks. Water will still remain in the pipes and could start smelling because it is not moving. This type of product will keep the water from stagnating and from smelling too bad. Governmental regulations sometimes prevent plumbers from actively providing maintenance to copper piping. If you have a calcium buildup in your copper piping, you are going to need to take care of this yourself. You have to get rid of all the water and add vinegar which eats away the calcium buildup out of copper pipes. When installing a brand new water heater, if you see a pipe from the drainage pipe, reconnect it. This is probably what is called a recirculation pipe. This keeps the water in your home heated while reducing the amount of water wasted. When it comes to plumbing, there is never an unsolvable problem. If you feel yourself becoming frustrated with the project, you should try to take a break from what you are working on. The greatest mistakes start to happen when you become angry and inpatient, so take a break and walk outside. When facing temperatures below freezing in the winter it is important to leave the hot water dripping. This makes sure that the pipes don't freeze over and saves you the expensive repair of fixing and or entirely replacing a broken pipe. The slight cost of dripping hot water is well worth saving you from that large expense of replacing a broken pipe. To prepare for the cold weather, properly drain all outside faucet bibs and turn off the water supply to those faucets. A piece of foam taped to the outside bib can provide excellent insulation to prevent any remaining water from freezing or splurge for a specialty cover that comes complete with velcro closures. Plumbing problems aren't so tough to deal with when you have knowledge of how to fix basic plumbing problems. Next time you're thinking of calling an expensive plumber, pull up this article instead and see if you can fix the problem yourself with the tips you've read here today.