Plumbing can cost a lot of money, so being prepared and knowing how to take care of your plumbing in Central Area can be very beneficial to you and your wallet. By knowing how to take care of your plumbing, you can save time and save yourself a lot of money, in the end.
If you have issues with the plumbing making a hammering sound when you turn it off, check your water pressure. Any time your water pressure is above 80 PSI, you will hear extra water noise. This can be easily solved by the installation of a pressure-reducing valve, which can be done by most homeowners.
If you have a clogged drain, don’t use cleaning chemicals to try to clear the clog. These harsh chemicals can corrode your metal pipes leading to leaks and broken pipes over time. Instead, stick to a plunger or make use of a plumbing snake to clear them.
Avoid using hard cleaners on your toilets, such as drop-in cleaner tabs in the tank. When these tabs are almost completely dissolved, what’s left of the tab gets washed into the bowl. This can then end up clogging the toilet’s port holes, preventing the toilet from flushing properly. It can take months for this debris to finish dissolving in those holes.
A sink hose that is installed incorrectly will lead to water flowing into the dishwasher. The hose leading from the kitchen sink to the dishwasher must lead uphill and then back downhill in order to prevent mixing of water from both devices.
The Best best plumbing and drain services near me in Seattle
Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there’s a place to recycle it near your home.
To avoid freezing pipes in the winter, make sure to insulate any exposed pipes in you basement before winter comes. Pay extra attention to pipes near the outside walls. If you have had a problem with any particular pipe freezing in the past, apply some heat tape to insulate those pipes.
If the hot water heater in your house is over ten years old, you should look at replacing it. Hot water heaters are very susceptible to corrosion on the bottom. This can lead to leaking and flooding whatever room it is in. Then not only will you have to replace it, but you’ll have to fix any damage caused by the leak.
Work with plumbers that offer flat rates. When a plumber in Central Area is charging by the hour, they do not have an incentive to get the job done quickly. It is human nature to go just a little bit slower if it’ll mean extra money in our pockets. If you cannot find someone who charges per project make sure that you are vigilant in watching the clock and their work.
Sometimes kitchen sinks can be clogged up due to a slow accumulation of solidified grease. One quick fix for this is to try pouring very hot grease down the sink, which will liquefy the grease clogging the drain and carry it down. Water won’t work, because grease will not dissolve in water.
The key to finding a great plumber for new construction is to look at their prior jobs. Good plumbers take pride in the work they do, so they will have photos and references from previous jobs. If the plumber you are considering hiring does not have references or photos of previous jobs, then stay away and find another.
If you are thinking about becoming a plumber yourself, then you should first try to start out as an apprentice. If you can find a good mentor then you will learn a great deal more from watching and assisting him than you possibly could learn by working on projects alone.
Never try to undertake a project that you are unsure of. Additionally, never call on a friend to help you with something, if they are not a professoinal. There have been hundreds of good friendships ruined by a guy claiming to know exactly what he is doing, when the truth is he is clueless.
If you have an ice maker or other plumbing going to your refrigerator, every six months or so pull the refrigerator away from the wall and inspect this plumbing. There should be no condensation or corrosion on these plumbing lines, if there is, contact a plumber and have them look at it.
Be sure to have a running toilet fixed as soon as you can. Having a running toilet uses more water, which raises your water bill. To fix it yourself, you just have to find out what the problem is and buy the supplies you need. If you can’t fix it yourself, call a plumber.
Sometimes in the case of minor and or major emergencies we all have to become Mr. Fix it ourselves. If you’ve got blockage in your drains the first step is to try a commercial de-clogger like Drano. Simply pour it down the drain, wait ten minutes, and presto, your drain should be clear.
It is a general rule of thumb that you should replace a water faucet every seven years, even if you do not see anything wrong with it. Some faucet problems are not visible to the naked eye, which is why it is so important for them to replaced every so often.
If you are going to update the plumbing in your house, one thing to consider is installing a new tank-less water heater. They are much smaller than traditional tank heaters, which is a space-saver. Tank-less water heaters are available in gas or electric, depending on what your house needs.
By knowing your plumbing and how it works, as was stated before, can save you a lot of time and money. There’s nothing worse than a plumbing accident to mess up your day. So, using the advice from this article, you can be sure to save yourself a big headache!
- Hi guys, welcome to thisplumberparts. Co. Uk video, today we're looking atthe exciting installation of a shower tray. So watch the video. Remember to subscribe,remember to follow us on Facebook and Twitter, andalso remember to hold tight. See you soon. - [Announcer] Plumerparts. Co. Uk, Home of Find Your Plumber. - Right then guys so, oh, have I got anything in my hair? Don't worry, sorry about that. I'm gonna look like anidiot in this video. Anyway right, so what we'vegot is our shower tray is just going up here somewhere. And I'm pretty sure Ihave preliminary measured out already, and as islife, the shower tray weights outlet is 100%gone over the top of joist. It's probably goingover where some of those pipes are already, soit's one of those things. So without going into too much detail, I'm just gonna do this job and you guys can just follow us in the background. We're gonna get to a stage route. We're not gonna go into this box here that we fitted a few days ago. We're not gonna go into that. We just need to get ourengine half-pipe down into this area here, okay? We can't put a box in right up there because we cannot physically drill through those two joists, becausethey're so close together. We can't get a drill inthat way or that way. It's just bloody nightmare. So what we're gonna dois we're gonna run along our weights pipe, our inchand a half across down here, and then we're gonna drop it down so it's inside this cupboard. So eventually, in this area here, this is all gonna be cupboarded in, it's gonna have an unvented cylinder in here,which we're gonna fit as well. I'm sure you'll be alongfor the ride on that one. So yeah, that is what we're gonna do. You're just gonna watch, sitthere with your cup of tea, in the bliss of your bed and watch us struggle away on a Saturday morning, Saturday bloody weekend warrior, and get this done. Enjoy. So you guys, this area herehas been precisely laid out for this shower. Basically the guys who've come in here and they've boxed this bit in. So effectively, all wegot to do is we've got to lay the shower drain down in here now, and we're gonna draw a circlewith the shower tray hole where the trap goes out, and guess what? That means that's wherethe bloody shower tray outlet is gonna be, isn't it? So we got to get the shower in now, which Mark, who's off-shore at the moment, has very kindly bought Ithink the world's heaviest shower tray, but it doesn'tmatter because I'm doing the tubes this morning, so you know. So I'm gonna get it now. Where is the bloody thing? So we're gonna cut up our big stuff open. Now this is one of them moments in life you wish you brought someof those window suckers, 'cause whatever happens,you might cut yourself on this stuff, so be careful. Don't do what I'm doingand do this without gloves. How exactly did they do this Mark? - [Mark] Flatten 'em. - Okay, put it down a little bit. Standard shower trap. It'll usually come with a little tool, because once you got your part work and everything underneath,the work you're gonna do is gonna be from above. So the little tool iseffectively used to cram into one of these little slots here. You can imagine my handis the shower tray, it'll scoop down into that like that, then underneath you'vegot your rubber seal, just under here, that will be going up the underside of my hand, so therefore the underside of the shower tray, and then all that gets pulledup, together like that, to make a water-tight seal underneath. Take the decorative coveroff, the facial cover. The bit you'll put inonce this is all tiled, once these have got windows and doors, and everything else is done. So we've got our hole here. Now this is exactly whereour shower tray is gonna be, we've got a lovely little, perfect little gap just around here. So we now can draw out my hole, exactly in the place where I want it. So now we can lift up the shower tray. I'm just gonna pop itup there, outta the way out the corner, then we canlay our actual trap down, get our template ready for the trap. You can cut a hole out here for the trap, then cut a notch out,like this, to take this in a little bit, becausethis knuckle can sort of tackle the other side of the floor, and if this has been pushed out of light in anyway whatsoever, later on in the job and we come to tighten up, you won't get a water-tight seal, andyou'll have the amp. Alright, so do things like that to make it easier for you now. ♫ Oh a frown with golden brown (Graham hums) Make sure you store yourbeloved shower tray, and you're gonna put itsomewhere where it doesn't crack you around the head later on. Typically, it's a touch bit too small. Such is life, give us the old grunt work, where we gotta be. Well ain't that just typical. What we're gonna do,I'm gonna set up this, that does that, okay? So we go down, we look over the top, and we go, "Right, I'mgonna cut this bit. " That's where we're gonna run. Don't leave yourself anywhere where this can get sort of inhibitedor anything like that. Or bugger about it. At the same time, asyou can see down here, we've got joist. Now this is where coordinationbetween the trades on a job like this or any extension or any kind of new build sort of stuff. When the architects andstuff design these bases or build a control. Say you've got to havejoist in certain positions, there is times where this happens. I mean it actually happens more often than it doesn't, if you know what I mean. It's quite a common problem. So what we have to do is we coordinate with chippies or builders,and say, "Look guys, "I've got to take this joist out. "They don't want the showerto be another way around. "If we put the wasteironing on the corner, "I might not get the job that I need "to get over to the stack. " So there's a lot of thingsthat you have to think about when you're doing this sort of thing. What we'll do is I'll nowgo ahead, put my weights in, and then on Monday, whenthe chippies have got off their asses, becauseI never work weekends, they will come in andbasically sort this out. They'll have to strengthen it. Then what'll happen is we'llget building control around, they'll have a look at itand sign it off, basically. So that's value. So I want you to feelwhat we were thinking, so when you get to pullthis out, you've got to go down the ole drill. Alright, let's just get downthere and split this out. We are just gonna notch out a little bit, this little rung that we'vekind of knotted out here. Before we do anything with a shower tray, before we lock that downor anything like that, I want to make sure that this can sit in there freely and move about. So it's got like a goodfive to 10 mil around it. Any problems with the showertray later in the job, we're making it now easierfor us in the future. So you can't deny, Imean a lot of plumbing is just prep work, really. So look at that lovely bitof wood butchery there. But the main thing is nowis we can sit this in here, and it's completely flush with the bottom of the floor, so in aminute when we've got our shower tray here,and look at what movement has got as well. It's not tied up or anything like that. That means we can do allour work now from above without having to worry. We can even tighten up, you know the bit of the job that peoplehate, when you tighten up the shower trap? You know, you're not nextto it, anything like that. You can even do that now from above without having to worry too much. So a couple of tips forthis bit, number one: Every shower tray that'sever made, to be honest, this one here. Okay Mark is due, he boughta good quality one here. A lot of the time you get under here, this is just like rippled up and horrible, and yeah, difficult to seal up. Now I know that we obviouslygot our rubber seal. This is gonna go onunderneath just like this, and that is where our mainseal is gonna come from. To be honest, look at this. I'm so happy with it. Sometimes what I do is I run a little bit of gunk around here just to be sure. I felt good here anyway. I always do, it's justone of those things. Now every brand new showertray that's ever been made, they always have this littleprotective film on it. Don't pull off the whole film, okay? Leave the film overit, as long as you can, but for the bit aroundwhere we're gonna be doing our seal now, you'regonna wanna pull that film away just there. What I mean by that is just rip here. Ready for us. Just gonna put a littlebit of CT1 on here. Just leave it like that. What they would say is begood to the next person who's coming along, and ifyou got any CT1 spittering out the side or anythinglike that, just make sure you smooth that off now. Otherwise someone might comealong again to do some work here and they won't be ableto take the whole trap off, and that wouldn't be very nice, would it? Alright, so we pop our trap on here, making sure that allour other bits and bobs are outta the way. Put it in that direction. Here's the little toolthat I was talking about. Usually you just get thisin here and get this on. Well that is not gonna leak. We are literally nowjust a matter of getting yourself a sheet, clean off as much dust and snot like that from underneath. Brush as well. Brush up wherever you put the shower. Try to make sure thisis as clean as possible. This is totally fat, this shower tray, weighs an absolute tonne. If you just laid it on the floor and tried to kick the bloody thing,it wouldn't move anywhere. So what we're gonnado, we're gonna use our clear CT1 to actually gluethis down, stick it down. We'll also run a beakeraround the outside as well. After that, once that isset, literally the floor will come up with the shower tray. That stuff, it grabs on anything. So I'm just gonna quicklyclear this part up, give us a wipe down,then we're just gonna. We're gonna do it in blobs, I think blobs don't really work too well. You do these little blob points here. I just want a ring aroundthere, ring around there, ring around there, allthose little rings there and just try and run a fewup these lines here as well. It will not move anywhere, this stuff. Obviously I've cut myself a larger hole so we're not doing it as well. Important thing is here that you clean down the bottom of the shower tray. We know that there's not gonna be any dust or anything like that. Can stop this adhesive doing it's job. Even though this stuff isjust different level, really. What happens now is you basicallymove this round in a very little to attempt to get anyCT onto yourself as well. Never easy this bit, I'm afraid. And literally, that should just lay the exact way I wantit, without any problems whatsoever, look at that. We can just pop this in here now. Right, what I do now, just peel up. Remember guys, just the edges. Right then, so that'sthe shower tray down. What we need to do now is go downstairs, plant our pipe root an inch and a half, then actually get ourinch and a half installed. Right then guys, so we'vegot our 45 bit on here, so we know we can get a nice straight run, so I'm just gonna pop thisbit on now underneath. Get that as nice and tight as possible. Now obviously the problem we've got here is that we've got pretty three of joist to go through until we'reinside our cupboard area, where we can drop ourpipe down safely inside that cupboard, out of sight. Obviously you want to tryto put one bit of pipe in. Sometimes that's just notgonna happen, alright. We're gonna have quitea high hole height here, and without ripping the floor up, this all will be glued down andscrewed down already. The only way we're gonna be able to get this through at themoment is to literally, it's annoying, reallyannoying, is to basically grab a couple of couplingsand just basically glue up a few bits. So what I firstly recommendis when you're measuring your holes, just measure everything from your bottom joist, because you know these are all level, and makesure that every joist you go in on, just giveyourself another two mil. Drop yourself another twomil down, or if you want to do a little bit more, another five mil, it's totally up to you. Just make sure you geta nice, adequate draw. Going away. You're doing quite along run, then obviously you don't want to do toomany mils every joist, otherwise you're gonna endup popping out the ceiling. This is quite short aroundhere, so I can probably get away with giving myselfpretty much five mil drop on every one of these joisthere, and that work fine. Similarly, if this wasrunning the other way, what I'd do is I'd take my waste back to the side joist, sowe were going long here, and I'd clip it all theway along the joist, okay? And then when you put your clips in, you measure your clips down five mil every time to make sure youget an adequate drop on that. So I'm going to get these measured up now, I'm gonna get 'em drilled,and then we're gonna go through the rigamarole ofgetting this pipe put in. Well what I'm doing,I'm leaving this pipe, coming out of the wall,quite far off the wall because this one needs to be boarded out in here anyway, so this will leave the lads a little bitof room, so I can get in there with there. Under there where there'stroughs or whatever. Well there we go, all in. I'm really, really happy with the result. I mean it wasn't easygetting through those bits, and I hope you'llunderstand why we've done certain parts of this job. I just want to get acrossto people that everything is completely differentwhen it comes to these jobs. There's no right or wrongway of doing things. Sometimes it's just the onlyway, if you know what I mean. Right then guys, so there you go. Shower tray's laid down,we've got the weights downstairs all in. We're now ready for the other trays to come in and do theirstuff and it's the blissful world of a plumber knowingthat everything's done and that you don't have to worry anymore for another month. Anyway I hope you enjoyed the video, guys. Remember to pop over toour Facebook and Twitter, follow us there. There's links comingup now to buy T-shirts. The same T-shirt as whatI'm wearing right now. And all sorts of linksto some other videos. Anyway, I hope you have a great time, and I'll see you soon guys. Hold tight!.
Welcome back to another plumbing trickvideo. If you're not used to doing threaded black steel piping, here's aneat trick that'll save you time and money when working with 3/4" inch and1" diameter piping. When taking your measurement place your tape measure on the face of your fitting to the center of where your pipe needs to go andthat's your final measurement. If you don't have the right size pipe clamphere's an old-school trick that will secure your pipe temporarily till youget the right clamp. Grab your adjustable wrench and bend the tail end of the clip,this will make it fit a smaller pipe and will get you out of trouble at no extracost if you're stuck. Whenever cutting any type of pipe, they need to be cutstraight. If you don't have your wrap around here's a good alternative that'llgive you very similar results. Get yourself a hose clamp that fits pipesize and scribe your line to be cut, a straight line guaranteed every time. There are many ways to salvage a used PVC fitting that's already been gluedas seen in my previous videos. But here's another cool way to get it done. Get yourself a heat gun and heat the assembly thoroughly till it's softenough to insert some needle nose pliers between the fitting and the pipe. Then,grasp the pipe really good and twist it until it comes right out,use this method in a well-ventilated area. And as a last trick, getting to thebottom of your dope cans isn't always easy. You could cut them in half, orsimply pound the can till you reach the bottom, saving you money in the long run. If you guys like these trick videos, I invite you to LIKE, SHARE & SUBSCRIBEfor more and if you have any suggestions or ideas for future trick videos let meknow I'll be glad to include them in my next one. I'll see you guys in the nextvideo.
When you think of plumbing, do you just see it as a hidden and mysterious network of pipes and pumps that makes your toilets and sinks work? If so, then you are very unlikely to have a go at mauntaining or repairing the system. Plumbing is not actually that complicated, and there are many things that you can do yourself to maintain and repair your system. Read on to find out how.
On very cold winter nights, allow your faucets to trickle slightly, especially if your pipes are located in a crawlspace. The running water prevents the pipes from freezing as quickly as they would otherwise. You can catch the water and use it for other household needs to prevent wasting it.
Check how well your toilets are flushing. If the handle needs to be played with in order to keep the water from running constantly, or if it needs to be held down several times in order to flush, you may need to switch out some of the parts in your tank. This is not expensive, and it could help reduce your monthly water bill. It could also mean that you avoid the embarrassment of the flushing system breaking when you have visitors!
Find a better way to discard of cooking oil instead of pouring it down the drain where it can easily clog your pipes. Keep a coffee can or other metal container handy to pour grease into after cooking. Place the can in the freezer to harden the grease and when it's full, discard it with the trash.
Use strainers in all drains to catch hair and other objects. This will prevent all the material from going down the drain and causing a clog, which can cause a bigger problem down the line. Clean out the strainers daily so that you don't start getting backup of water in your sink or tub.
Make sure that you disconnect all hoses outside your house when the fall season hits. This is important to reduce the chance of freezing, which can cause damage to the connecting pipes. Disconnect all of your water hoses and store them safely to put your family in the best position for the fall.
If your drain in any device is taking longer to drain water, then you may need to have your pipes professionally cleaned depending on the severity of the circumstances. Before you do this, there are several different products you can try. However, some of them are professional strength and all products should be used with caution.
Make sure you get a good recommendation or check the references before you hire a plumber. With good recommendations, it will assure that you are hiring an experienced plumber. If the experienced plumber is professional, he will have a fully stocked truck and be able to complete most small jobs in one visit.
If you live in an area that sees routine freezing temperatures, make sure you do something to keep your pipes from becoming frozen as well. There are a wide variety of ways you can keep your pipes from freezing, which will help you avoid damage to your home and costly repairs.
Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there's a place to recycle it near your home.
If the hot water heater in your house is over ten years old, you should look at replacing it. Hot water heaters are very susceptible to corrosion on the bottom. This can lead to leaking and flooding whatever room it is in. Then not only will you have to replace it, but you'll have to fix any damage caused by the leak.
When you're going away on a vacation, you should consider shutting off the water supply to your home. This can help stop many problems before they start. If you don't do this, you should have someone stop by your house regularly to check that nothing has gone wrong and that your home isn't flooded.
Realize that branch lines can get blocked and cause sewage backups that affect main lines. If you can't clear the blockage yourself, contact a professional plumber, who can insert a snake into the line to break up the blockage.
Do not pour grease and oil down your drains. Cooking grease will build up in your pipes and could cause back-ups. Keep grease and oil in a container in your fridge and throw it in the trash when it is full. Avoid clogging your pipes with any products containing oil or grease.
If you are seeing areas in your ceiling or walls that appear to have water damage or are sagging, make sure you turn off the power before inspecting. Electricity and water do not mix. The last thing you need is to go into the attic and get shocked by a pool of water.
To avoid plumbing disasters in your kitchen, never place hard-to-grind, stringy, fibrous waste, such as poultry skins, banana peels, carrots, celery, or cantaloupe pulp, into the garbage disposer. The disposer can't sufficiently grind these food products and they will clog your sink drain. You should also run cold water down the drain for about 15 seconds before and after using the garbage disposer to flush the waste down the main drain.
When it comes to plumbing a great choice is to invest in brass fittings. Sure, they may be more expensive upfront, however their longevity is amazing compared to the alternatives, so you end up saving money. As an added bonus, the brass fittings look so much better than the other alternatives.
It should not be necessary to call out a professional for every repair job. If you take your time and apply sensible advice, such as what you read here, you can successfully repair many of the common faults that develop. It may take a longer the first few times, but after a few successes you will pick up speed.
Think Home Service Does best plumbing and drain services near me