Plumbing can cost a lot of money, so being prepared and knowing how to take care of your plumbing in Ballard can be very beneficial to you and your wallet. By knowing how to take care of your plumbing, you can save time and save yourself a lot of money, in the end.
If you have issues with the plumbing making a hammering sound when you turn it off, check your water pressure. Any time your water pressure is above 80 PSI, you will hear extra water noise. This can be easily solved by the installation of a pressure-reducing valve, which can be done by most homeowners.
If you have a clogged drain, don’t use cleaning chemicals to try to clear the clog. These harsh chemicals can corrode your metal pipes leading to leaks and broken pipes over time. Instead, stick to a plunger or make use of a plumbing snake to clear them.
Avoid using hard cleaners on your toilets, such as drop-in cleaner tabs in the tank. When these tabs are almost completely dissolved, what’s left of the tab gets washed into the bowl. This can then end up clogging the toilet’s port holes, preventing the toilet from flushing properly. It can take months for this debris to finish dissolving in those holes.
A sink hose that is installed incorrectly will lead to water flowing into the dishwasher. The hose leading from the kitchen sink to the dishwasher must lead uphill and then back downhill in order to prevent mixing of water from both devices.
The Best professional plumber near me in Seattle
Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there’s a place to recycle it near your home.
To avoid freezing pipes in the winter, make sure to insulate any exposed pipes in you basement before winter comes. Pay extra attention to pipes near the outside walls. If you have had a problem with any particular pipe freezing in the past, apply some heat tape to insulate those pipes.
If the hot water heater in your house is over ten years old, you should look at replacing it. Hot water heaters are very susceptible to corrosion on the bottom. This can lead to leaking and flooding whatever room it is in. Then not only will you have to replace it, but you’ll have to fix any damage caused by the leak.
Work with plumbers that offer flat rates. When a plumber in Ballard is charging by the hour, they do not have an incentive to get the job done quickly. It is human nature to go just a little bit slower if it’ll mean extra money in our pockets. If you cannot find someone who charges per project make sure that you are vigilant in watching the clock and their work.
Sometimes kitchen sinks can be clogged up due to a slow accumulation of solidified grease. One quick fix for this is to try pouring very hot grease down the sink, which will liquefy the grease clogging the drain and carry it down. Water won’t work, because grease will not dissolve in water.
The key to finding a great plumber for new construction is to look at their prior jobs. Good plumbers take pride in the work they do, so they will have photos and references from previous jobs. If the plumber you are considering hiring does not have references or photos of previous jobs, then stay away and find another.
If you are thinking about becoming a plumber yourself, then you should first try to start out as an apprentice. If you can find a good mentor then you will learn a great deal more from watching and assisting him than you possibly could learn by working on projects alone.
Never try to undertake a project that you are unsure of. Additionally, never call on a friend to help you with something, if they are not a professoinal. There have been hundreds of good friendships ruined by a guy claiming to know exactly what he is doing, when the truth is he is clueless.
If you have an ice maker or other plumbing going to your refrigerator, every six months or so pull the refrigerator away from the wall and inspect this plumbing. There should be no condensation or corrosion on these plumbing lines, if there is, contact a plumber and have them look at it.
Be sure to have a running toilet fixed as soon as you can. Having a running toilet uses more water, which raises your water bill. To fix it yourself, you just have to find out what the problem is and buy the supplies you need. If you can’t fix it yourself, call a plumber.
Sometimes in the case of minor and or major emergencies we all have to become Mr. Fix it ourselves. If you’ve got blockage in your drains the first step is to try a commercial de-clogger like Drano. Simply pour it down the drain, wait ten minutes, and presto, your drain should be clear.
It is a general rule of thumb that you should replace a water faucet every seven years, even if you do not see anything wrong with it. Some faucet problems are not visible to the naked eye, which is why it is so important for them to replaced every so often.
If you are going to update the plumbing in your house, one thing to consider is installing a new tank-less water heater. They are much smaller than traditional tank heaters, which is a space-saver. Tank-less water heaters are available in gas or electric, depending on what your house needs.
By knowing your plumbing and how it works, as was stated before, can save you a lot of time and money. There’s nothing worse than a plumbing accident to mess up your day. So, using the advice from this article, you can be sure to save yourself a big headache!
My name is Tom Roberts and on behalf of the Australian Building Codes Board, I'd like to welcome you to the update of the future of the Plumbing Code of Australia. Topics covered in this presentation include the history of the PCA, an overview of the regulatory framework surrounding the PCA, important information on how the NCC has changed, projects being conducted by the ABCB, intended for NCC 2019, key dates for the NCC development cycle, and how to register for the NCC. So where does the Plumbing Code of Australia or PCA sit within the regulatory framework? When you look at planning nationally, you can see the PCA and the rest of the national construction code is called up by state and territory legislation. The ABCB works within this area. Technical reference documents such as Australian standards are called up in the PCA. The PCA sets out the role of standards it calls up, and which parts and editions should be used. Administrative matters such as licensing approvals are retained in the regulations and not part of the NCC. The national construction code consists of the Building Code of Australia or BCA, which is the NCC Volume 1 for Class 2 to Class 9 buildings, and NCC, Volume 2 for Class 1 and 10 buildings. The Plumbing Code of Australia, NCC Volume 3 is for all classes of buildings. Historically, the regulation of plumbing and drainage in Australia has developed in close alignment with state and territory water and sewage authorities as they are regulated for sanitary drainage and water supply. The National Planning Regulators Forum or NPRF was established in 2002 with representatives from states and territories to develop the Plumbing Code of Australia. The PCA 2004 was published, however, only adopted by Queensland, South Australia, Tasmania, Victoria, and the ACT. In 2010, the PCA was reviewed as part of initiatives to incorporate all on-site construction requirements into a single code. The PCA 2011 was released as Volume 3 of the NCC by the ABCB. From 2011 to 2016, there was an annual change to the PCA, however, from 2016 onwards, the NCC has moved to a three year amendment cycle to provide greater stability for industry. During the lead up to NCC 2019, the ABCB has been able to focus on a number of projects to improve the PCA. The 2016 edition was the first NCC edition to be freely available online. So what's been done by the ABCB while not publishing its annual amendments to the PCA? The main projects include the development of acceptable plumbing practices, plumbing research in four main areas: backflow prevention, rainwater harvesting and use, fixed unit ratings, and warm water systems. The harmonization of the PCA and the BCA, the development of Australian Standards are another of other ABCB projects. I mentioned before acceptable plumbing practices, or APP, but what is it? An APP is an optional means of compliance with the performance requirements of the PCA. Similar to the structure of Volume 2 of the BCA, which contains acceptable construction practices, an APP would provide a simple solution, veneer single, detached slab on-ground Class 1 or Class 10 buildings. This will give practitioners the option of using reference documents such as ANZ/AS 3500 or the APP for these simple building types. The content of an APP will be developed based on the content of the New Zealand building code where it is also used as a compliance option. How would an APP fit into the regulatory framework of the PCA? As you can see on the slide, there's still an option of undertaking the performance or Deemed-to-Satisfy solution to meet the performance requirements of the PCA. Reference documents such as AS/NZS 3500 will remain the primary means of compliance for Deemed-to-Satisfy solutions and will still apply to all classes of buildings. However, for new single, detached slab on-ground Class 1 or Class 10 buildings, the APP will also be an option freely available and contained within the PCA. The Plumbing Code of Australia Research and development project was commenced in four areas of plumbing and drainage which were identified requiring exploration. These four areas include: backflow prevention, rainwater harvesting use, warm water systems and fixed unit ratings. Backflow prevention research has resulted in a report based on the desktop survey and preliminary targeted consultation which was released in 2015 for public consultation. Some of the key findings of the report discussed errors such as registration and testing which were considered to be not consistently enforced. That cross connections generally occur in individual and or agricultural situations and are also under reported. There was no evidence of widespread failures with general causes of being lack of awareness, poor design or mistakes. The only consequences, not the probability or likelihood, is considered in the risk assessment. Regulatory reliance on informative Appendix G of AS/NZS 3500 Part 1. The application to non-drinking water installations is unclear. Containment protection, application and responsibilities are unclear. The report contained recommendations for further work which the ABCB Board endorsed for the ABCB offers to progress. These consisted of containment protection outlined by both the network utility operators and within the PCA with greater engagement to aid the consistency. The development of cross connections control manual clarified above-ground rainwater tanks as low hazard. Probability in consequence risk methodology, a Deemed-to-Satisfy version of Appendix G to be developed and to be contained within the PCA. Clarification of backflow prevention requirements for non-drinking water supplies. Development of Deemed-to-Satisfy for access and maintenance solutions. Consolidation of NUA containment provisions within the PCA. Rainwater harvesting and reuse has resulted in a report which explored regulations, standards and guidance material and similar to the backflow prevention report, consisted of targeted consultation. The report was released in 2015 for public consultation. The key funding to the research confirmed national inconsistency. The recommendation of the report were endorsed by the ABCB Board for the offers to progress. These recommendations included increased engagement with affected industry stakeholders to promote national consistency. To recognize rainwater harvesting in the PCA for a new part. Clarify the application of the PCA with relation to rain water in other parts. Clarify the status of rainwater tanks used for bush fire control. Develop a non-mandatory handbook for the National use and current regulatory controls identified. Research on warm water systems has intentionally been selected as there is currently no prescriptive solutions in the PCA for these systems. The research resulted in a report outlining literature on design installation and maintenance of warm water systems. The development of a Deemed-to-Satisfy solution for warm water systems was not progressed due to the site specific nature of the systems, and the multiple means of Legionella and scolding risk mitigation strategies. The report was released for public consultation in 2015 and was updated based on the comments received through public consultation. The report has since been reformatted into a draft ABCB handbook and a peer review is currently being undertaken by consultants to ensure the information provided within the handbook is technically accurate and complete. Once reviewed and endorsed by the ABCB Board, the handbook will be made publicly available to provide guidance to practitioners. The final research project relates to a fixed unit ratings. This project was selected as current methods for pipe size and calculations are based on almost 80-year-old methods developed in the USA. Research resulted in a discussion paper being developed by consultants and was released by the ABCB in 2015. The paper explored the origins of current fixed unit ratings, basis and value of overseas equivalents, and comparisons with the Australian context. And the overview of the system design methodology using current fixed ratings. Numerous comments were received on this paper which is available on the ABCB website. ABCB will look further into this research throughout 2017 with a project plan currently under development based on the recommendations received through public consultation and the consultants. Another important project being undertaken by the ABCB is the harmonization of the building and plumbing codes which make up the NCC. There are a number of specific areas being investigated, some minor in nature and some are quite complex. These issues include areas such as: boilers and pressure vessels, swimming and spa pool plant and drainage, undue noise, stormwater, firefighting water services, heating ventilation and air conditioning provisions. Another area for the ABCB has a large amount of involvement with the development of the PCA reference documents. The ABCB is the link between the Plumbing Code Committee and the Committees of reference documents such as the Australian Standards WS14 committee. This involves keeping the plumbing code committee informed and consulted on, and it allows input at key stages during the development of the process. The role of the ABCB is also to assist the committees with compliance with the ABCB protocol for the development of NCC reference documents. The protocol ensures that the documents are prepared or revised are appropriate for a regulatory use, undergo consistent and transparent process, and are delivered in a suitable format and drafting style. There are a number of projects being undertaken by the ABCB which have an effect on the 2019 edition of the PCA. These include the NCC readability. This involves repackaging of the NCC to simplify its use and therefore make it more accessible to a wider audience that are exposed to the NCC as a result of making it freely available online. The initiative will initially relate to the NCC language and to a lesser extent, the NCC format. NCC digitization improvement look to enhance practitioner access in understanding of the NCC for a range of new and refreshed technologies The ongoing consolidation of state and territory plumbing regulations into the PCA, ongoing work to reduce state and territory variations to the PCA. So how does changes occur to the NCC? Changes to the NCC can be the result of a number of things such as government policy decisions, ABCB Project Work, proposals for change, or a change to a reference document. Those seeking to propose a change are required to submit justification to support the proposal. This justification should be proportionate to the size of the proposed change or its potential impacts. Justification should include a description of the proposal, an explanation of the problem it is designed to resolve. Evidence of the existence of the problem. How the proposal is expected to solve the problem. What alternatives to regulation have been considered? And why were they not preferred? Who will be affected and how will they be affected? And any consultation that has been taken. Any proposed changes to the PCA are considered by the plumbing code committee and for the BCA, the building codes committee. Proposed changes to the NCC are released for public consultation, and after comments are considered, changes are finalized and submitted to the ABCB Board for their final consideration and endorsement. NCC development dates. The Building Ministers Forum, or BMF, made the decision to move to a three-year amendment cycle following the 2016 edition to allow the ABCB to make the most of an effective use of resources, reduce unnecessary churn and focus on priorities. This means that the next scheduled update to the NCC will be in 2019. The key dates in the development of NCC 2019 are: the 1st September 2017 when the proposal for change submission process closes. The 2019 public comment draft will be available between the 1st February and the 13th of April in 2018. And the 2019 NCC will be available online in February 2019, and will be adopted by states and territories on the 1st May in 2019. How do you register for the NCC? The registration is a simple process. Firstly, log on to the ABCB website at abcb. Gov. Au and click the registration button on the top right of the homepage. You will then be asked to enter contact information and create a password. You'll also be asked if you wish to be updated on important information on NCC related materials, news events by email. Then click Register and you'll gain access to the NCC and other ABCB resources. So why register for the NCC? Other than to gain access to the NCC and other ABCB resources, free online registered users who have opted to receive communications will be advised when the public comment draft is available. You will also be alerted to when the ABCB is undertaking consultation activities such as part of regulatory impact analysis processes, or consideration of alternatives to regulation such as education and awareness-raising activities. Changes to the PCA affect all of the plumbing industry so more registrations are needed to keep industry informed of the work being done by the ABCB. Thank you for viewing the update on the future of the Plumbing Code of Australia.
- Hi guys, welcome to thisplumberparts. Co. Uk video, today we're looking atthe exciting installation of a shower tray. So watch the video. Remember to subscribe,remember to follow us on Facebook and Twitter, andalso remember to hold tight. See you soon. - [Announcer] Plumerparts. Co. Uk, Home of Find Your Plumber. - Right then guys so, oh, have I got anything in my hair? Don't worry, sorry about that. I'm gonna look like anidiot in this video. Anyway right, so what we'vegot is our shower tray is just going up here somewhere. And I'm pretty sure Ihave preliminary measured out already, and as islife, the shower tray weights outlet is 100%gone over the top of joist. It's probably goingover where some of those pipes are already, soit's one of those things. So without going into too much detail, I'm just gonna do this job and you guys can just follow us in the background. We're gonna get to a stage route. We're not gonna go into this box here that we fitted a few days ago. We're not gonna go into that. We just need to get ourengine half-pipe down into this area here, okay? We can't put a box in right up there because we cannot physically drill through those two joists, becausethey're so close together. We can't get a drill inthat way or that way. It's just bloody nightmare. So what we're gonna dois we're gonna run along our weights pipe, our inchand a half across down here, and then we're gonna drop it down so it's inside this cupboard. So eventually, in this area here, this is all gonna be cupboarded in, it's gonna have an unvented cylinder in here,which we're gonna fit as well. I'm sure you'll be alongfor the ride on that one. So yeah, that is what we're gonna do. You're just gonna watch, sitthere with your cup of tea, in the bliss of your bed and watch us struggle away on a Saturday morning, Saturday bloody weekend warrior, and get this done. Enjoy. So you guys, this area herehas been precisely laid out for this shower. Basically the guys who've come in here and they've boxed this bit in. So effectively, all wegot to do is we've got to lay the shower drain down in here now, and we're gonna draw a circlewith the shower tray hole where the trap goes out, and guess what? That means that's wherethe bloody shower tray outlet is gonna be, isn't it? So we got to get the shower in now, which Mark, who's off-shore at the moment, has very kindly bought Ithink the world's heaviest shower tray, but it doesn'tmatter because I'm doing the tubes this morning, so you know. So I'm gonna get it now. Where is the bloody thing? So we're gonna cut up our big stuff open. Now this is one of them moments in life you wish you brought someof those window suckers, 'cause whatever happens,you might cut yourself on this stuff, so be careful. Don't do what I'm doingand do this without gloves. How exactly did they do this Mark? - [Mark] Flatten 'em. - Okay, put it down a little bit. Standard shower trap. It'll usually come with a little tool, because once you got your part work and everything underneath,the work you're gonna do is gonna be from above. So the little tool iseffectively used to cram into one of these little slots here. You can imagine my handis the shower tray, it'll scoop down into that like that, then underneath you'vegot your rubber seal, just under here, that will be going up the underside of my hand, so therefore the underside of the shower tray, and then all that gets pulledup, together like that, to make a water-tight seal underneath. Take the decorative coveroff, the facial cover. The bit you'll put inonce this is all tiled, once these have got windows and doors, and everything else is done. So we've got our hole here. Now this is exactly whereour shower tray is gonna be, we've got a lovely little, perfect little gap just around here. So we now can draw out my hole, exactly in the place where I want it. So now we can lift up the shower tray. I'm just gonna pop itup there, outta the way out the corner, then we canlay our actual trap down, get our template ready for the trap. You can cut a hole out here for the trap, then cut a notch out,like this, to take this in a little bit, becausethis knuckle can sort of tackle the other side of the floor, and if this has been pushed out of light in anyway whatsoever, later on in the job and we come to tighten up, you won't get a water-tight seal, andyou'll have the amp. Alright, so do things like that to make it easier for you now. ♫ Oh a frown with golden brown (Graham hums) Make sure you store yourbeloved shower tray, and you're gonna put itsomewhere where it doesn't crack you around the head later on. Typically, it's a touch bit too small. Such is life, give us the old grunt work, where we gotta be. Well ain't that just typical. What we're gonna do,I'm gonna set up this, that does that, okay? So we go down, we look over the top, and we go, "Right, I'mgonna cut this bit. " That's where we're gonna run. Don't leave yourself anywhere where this can get sort of inhibitedor anything like that. Or bugger about it. At the same time, asyou can see down here, we've got joist. Now this is where coordinationbetween the trades on a job like this or any extension or any kind of new build sort of stuff. When the architects andstuff design these bases or build a control. Say you've got to havejoist in certain positions, there is times where this happens. I mean it actually happens more often than it doesn't, if you know what I mean. It's quite a common problem. So what we have to do is we coordinate with chippies or builders,and say, "Look guys, "I've got to take this joist out. "They don't want the showerto be another way around. "If we put the wasteironing on the corner, "I might not get the job that I need "to get over to the stack. " So there's a lot of thingsthat you have to think about when you're doing this sort of thing. What we'll do is I'll nowgo ahead, put my weights in, and then on Monday, whenthe chippies have got off their asses, becauseI never work weekends, they will come in andbasically sort this out. They'll have to strengthen it. Then what'll happen is we'llget building control around, they'll have a look at itand sign it off, basically. So that's value. So I want you to feelwhat we were thinking, so when you get to pullthis out, you've got to go down the ole drill. Alright, let's just get downthere and split this out. We are just gonna notch out a little bit, this little rung that we'vekind of knotted out here. Before we do anything with a shower tray, before we lock that downor anything like that, I want to make sure that this can sit in there freely and move about. So it's got like a goodfive to 10 mil around it. Any problems with the showertray later in the job, we're making it now easierfor us in the future. So you can't deny, Imean a lot of plumbing is just prep work, really. So look at that lovely bitof wood butchery there. But the main thing is nowis we can sit this in here, and it's completely flush with the bottom of the floor, so in aminute when we've got our shower tray here,and look at what movement has got as well. It's not tied up or anything like that. That means we can do allour work now from above without having to worry. We can even tighten up, you know the bit of the job that peoplehate, when you tighten up the shower trap? You know, you're not nextto it, anything like that. You can even do that now from above without having to worry too much. So a couple of tips forthis bit, number one: Every shower tray that'sever made, to be honest, this one here. Okay Mark is due, he boughta good quality one here. A lot of the time you get under here, this is just like rippled up and horrible, and yeah, difficult to seal up. Now I know that we obviouslygot our rubber seal. This is gonna go onunderneath just like this, and that is where our mainseal is gonna come from. To be honest, look at this. I'm so happy with it. Sometimes what I do is I run a little bit of gunk around here just to be sure. I felt good here anyway. I always do, it's justone of those things. Now every brand new showertray that's ever been made, they always have this littleprotective film on it. Don't pull off the whole film, okay? Leave the film overit, as long as you can, but for the bit aroundwhere we're gonna be doing our seal now, you'regonna wanna pull that film away just there. What I mean by that is just rip here. Ready for us. Just gonna put a littlebit of CT1 on here. Just leave it like that. What they would say is begood to the next person who's coming along, and ifyou got any CT1 spittering out the side or anythinglike that, just make sure you smooth that off now. Otherwise someone might comealong again to do some work here and they won't be ableto take the whole trap off, and that wouldn't be very nice, would it? Alright, so we pop our trap on here, making sure that allour other bits and bobs are outta the way. Put it in that direction. Here's the little toolthat I was talking about. Usually you just get thisin here and get this on. Well that is not gonna leak. We are literally nowjust a matter of getting yourself a sheet, clean off as much dust and snot like that from underneath. Brush as well. Brush up wherever you put the shower. Try to make sure thisis as clean as possible. This is totally fat, this shower tray, weighs an absolute tonne. If you just laid it on the floor and tried to kick the bloody thing,it wouldn't move anywhere. So what we're gonnado, we're gonna use our clear CT1 to actually gluethis down, stick it down. We'll also run a beakeraround the outside as well. After that, once that isset, literally the floor will come up with the shower tray. That stuff, it grabs on anything. So I'm just gonna quicklyclear this part up, give us a wipe down,then we're just gonna. We're gonna do it in blobs, I think blobs don't really work too well. You do these little blob points here. I just want a ring aroundthere, ring around there, ring around there, allthose little rings there and just try and run a fewup these lines here as well. It will not move anywhere, this stuff. Obviously I've cut myself a larger hole so we're not doing it as well. Important thing is here that you clean down the bottom of the shower tray. We know that there's not gonna be any dust or anything like that. Can stop this adhesive doing it's job. Even though this stuff isjust different level, really. What happens now is you basicallymove this round in a very little to attempt to get anyCT onto yourself as well. Never easy this bit, I'm afraid. And literally, that should just lay the exact way I wantit, without any problems whatsoever, look at that. We can just pop this in here now. Right, what I do now, just peel up. Remember guys, just the edges. Right then, so that'sthe shower tray down. What we need to do now is go downstairs, plant our pipe root an inch and a half, then actually get ourinch and a half installed. Right then guys, so we'vegot our 45 bit on here, so we know we can get a nice straight run, so I'm just gonna pop thisbit on now underneath. Get that as nice and tight as possible. Now obviously the problem we've got here is that we've got pretty three of joist to go through until we'reinside our cupboard area, where we can drop ourpipe down safely inside that cupboard, out of sight. Obviously you want to tryto put one bit of pipe in. Sometimes that's just notgonna happen, alright. We're gonna have quitea high hole height here, and without ripping the floor up, this all will be glued down andscrewed down already. The only way we're gonna be able to get this through at themoment is to literally, it's annoying, reallyannoying, is to basically grab a couple of couplingsand just basically glue up a few bits. So what I firstly recommendis when you're measuring your holes, just measure everything from your bottom joist, because you know these are all level, and makesure that every joist you go in on, just giveyourself another two mil. Drop yourself another twomil down, or if you want to do a little bit more, another five mil, it's totally up to you. Just make sure you geta nice, adequate draw. Going away. You're doing quite along run, then obviously you don't want to do toomany mils every joist, otherwise you're gonna endup popping out the ceiling. This is quite short aroundhere, so I can probably get away with giving myselfpretty much five mil drop on every one of these joisthere, and that work fine. Similarly, if this wasrunning the other way, what I'd do is I'd take my waste back to the side joist, sowe were going long here, and I'd clip it all theway along the joist, okay? And then when you put your clips in, you measure your clips down five mil every time to make sure youget an adequate drop on that. So I'm going to get these measured up now, I'm gonna get 'em drilled,and then we're gonna go through the rigamarole ofgetting this pipe put in. Well what I'm doing,I'm leaving this pipe, coming out of the wall,quite far off the wall because this one needs to be boarded out in here anyway, so this will leave the lads a little bitof room, so I can get in there with there. Under there where there'stroughs or whatever. Well there we go, all in. I'm really, really happy with the result. I mean it wasn't easygetting through those bits, and I hope you'llunderstand why we've done certain parts of this job. I just want to get acrossto people that everything is completely differentwhen it comes to these jobs. There's no right or wrongway of doing things. Sometimes it's just the onlyway, if you know what I mean. Right then guys, so there you go. Shower tray's laid down,we've got the weights downstairs all in. We're now ready for the other trays to come in and do theirstuff and it's the blissful world of a plumber knowingthat everything's done and that you don't have to worry anymore for another month. Anyway I hope you enjoyed the video, guys. Remember to pop over toour Facebook and Twitter, follow us there. There's links comingup now to buy T-shirts. The same T-shirt as whatI'm wearing right now. And all sorts of linksto some other videos. Anyway, I hope you have a great time, and I'll see you soon guys. Hold tight!.
Ah, plumbing. There are just so many ways to define it as it doesn't mean the same thing to everybody. There are also so many ways that somebody can improve upon their own system at home. With so many ways to do things, you are probably wondering where you can begin. Try beginning with the tips below.
If you are paying someone else to do the plumbing in your home be sure that they are licensed in your state to do that work. Some people who have little or no knowledge of plumbing will try to pass themselves off as a pro. So you can see the importance of checking to see if your plumber is licensed. You should also see if you can find positive testimonials about the plumbers work.
Periodically check your pipes for leaks and cracks. These can be forgotten, since pipes are usually hidden away, but checking for leaks and cracks can help you identify a small problem before a big problem occurs. You may have to enlist the help of a family member to turn on and off the water stream as you are checking.
You can drastically reduce your utility bills with the installation of shower heads designed for better efficiency. Most households use a lot of hot water in the shower. Invest in an energy-efficient shower head and you could save a hundred dollar every year on your water bill.
Make sure you get a good recommendation or check the references before you hire a plumber. With good recommendations, it will assure that you are hiring an experienced plumber. If the experienced plumber is professional, he will have a fully stocked truck and be able to complete most small jobs in one visit.
In cold climate areas, sometimes the pipes in the plumbing system freeze. You can thaw them out without calling a plumber. Before beginning this process, open the faucet and begin thawing closest to the faucet and then move down the line as sections thaw out. One method you can use is to wrap the pipe with a heavy towel or burlap and then pour hot water over it, set a bucket underneath to catch the water.
Don't shrug off that trickle coming from your toilet as a small problem. Even the tiniest leak can be quite expensive in the long run as you end up wasting potentially hundreds of gallons of water. See if you can find the root of the leak, or seek out professional advice, and keep your toilet running efficiently.
You should always clean your dryer's lint trap. By doing this simple task, you can circumvent a great deal of trouble. including prevention of fires. Be sure to inspect the lint screen for any tears or holes. That could result in lint traveling down your pipes, and that may result in clogs and other issues that have to be dealt with.
If you are trying to decide on the material to use for your hose, stick with stainless steel. Stainless steel has a very solid construction and stays durable for many years, eliminating the need for replacement. Also, this material is less prone to bursting, which can yield severe plumbing issues.
The most important plumbing tip you need to know is -- how to turn off your home's main water supply. Once the water is shut off, you can investigate problems and figure out how to resolve them. Walk the family through the house and show them where all the water shut-off valves are, and how to use them.
Make sure to never leave any flammable liquids near your water heater. Certain liquids like gasoline, solvents, or adhesives are flammable, and if left too close to the water heater, can ignite. If you have to have these liquids in your basement, place it far away from your water heater.
If you are thinking about becoming a plumber yourself, then you should first try to start out as an apprentice. If you can find a good mentor then you will learn a great deal more from watching and assisting him than you possibly could learn by working on projects alone.
To prevent the most common kitchen sink clogs, avoid putting any sort of solid foods down your drain. Many foods, such as eggs and vegetable and fruit waste actually harden with exposure to cold water and over time can form clogs that are next to impossible to remove without professional help.
When you are working on any kind of plumbing project, you always need a backup person. This is because, when working with water, you never know when an emergency can happen and that second pair of hands can come in very useful! This can even be an unskilled person who can follow directions.
If you have unused cooking grease, do not pour it down your kitchen drain. The grease or oil can clog your drain and even cause irreparable damage. Instead, put the unused grease or oil into a plastic bag. Or, you can put the grease into an empty tin can, set it in the refrigerator to solidify, and then throw it away.
To conserve hot water each day, run your dishwasher late at night. This will help to maintain an adequate water level for your guests and for your chores in the morning or afternoon. Also, you can increase the supply of water available to you for cooking meals throughout the day.
If you are considering a plumbing project due to having what appears to be pink or red water have your water tested first. This coloration is likely due to having rust in your water, which an average plumbing project is unlikely to fix. The rust is likely coming from your well and installing a water softener there is the best remedy to the problem.
Yes, plumbing is quite a subject in that it is completely subjective by it's very definition. No two people view plumbing the exact same way. What one finds useful to their system, the other may not. These tips should have given you some advice on how to start with your own plumbing.
Think Home Service Does professional plumber near me