Plumbing can cost a lot of money, so being prepared and knowing how to take care of your plumbing in West Seattle can be very beneficial to you and your wallet. By knowing how to take care of your plumbing, you can save time and save yourself a lot of money, in the end.
If you have issues with the plumbing making a hammering sound when you turn it off, check your water pressure. Any time your water pressure is above 80 PSI, you will hear extra water noise. This can be easily solved by the installation of a pressure-reducing valve, which can be done by most homeowners.
If you have a clogged drain, don’t use cleaning chemicals to try to clear the clog. These harsh chemicals can corrode your metal pipes leading to leaks and broken pipes over time. Instead, stick to a plunger or make use of a plumbing snake to clear them.
Avoid using hard cleaners on your toilets, such as drop-in cleaner tabs in the tank. When these tabs are almost completely dissolved, what’s left of the tab gets washed into the bowl. This can then end up clogging the toilet’s port holes, preventing the toilet from flushing properly. It can take months for this debris to finish dissolving in those holes.
A sink hose that is installed incorrectly will lead to water flowing into the dishwasher. The hose leading from the kitchen sink to the dishwasher must lead uphill and then back downhill in order to prevent mixing of water from both devices.
The Best best plumbing contractors nearby in Seattle
Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there’s a place to recycle it near your home.
To avoid freezing pipes in the winter, make sure to insulate any exposed pipes in you basement before winter comes. Pay extra attention to pipes near the outside walls. If you have had a problem with any particular pipe freezing in the past, apply some heat tape to insulate those pipes.
If the hot water heater in your house is over ten years old, you should look at replacing it. Hot water heaters are very susceptible to corrosion on the bottom. This can lead to leaking and flooding whatever room it is in. Then not only will you have to replace it, but you’ll have to fix any damage caused by the leak.
Work with plumbers that offer flat rates. When a plumber in West Seattle is charging by the hour, they do not have an incentive to get the job done quickly. It is human nature to go just a little bit slower if it’ll mean extra money in our pockets. If you cannot find someone who charges per project make sure that you are vigilant in watching the clock and their work.
Sometimes kitchen sinks can be clogged up due to a slow accumulation of solidified grease. One quick fix for this is to try pouring very hot grease down the sink, which will liquefy the grease clogging the drain and carry it down. Water won’t work, because grease will not dissolve in water.
The key to finding a great plumber for new construction is to look at their prior jobs. Good plumbers take pride in the work they do, so they will have photos and references from previous jobs. If the plumber you are considering hiring does not have references or photos of previous jobs, then stay away and find another.
If you are thinking about becoming a plumber yourself, then you should first try to start out as an apprentice. If you can find a good mentor then you will learn a great deal more from watching and assisting him than you possibly could learn by working on projects alone.
Never try to undertake a project that you are unsure of. Additionally, never call on a friend to help you with something, if they are not a professoinal. There have been hundreds of good friendships ruined by a guy claiming to know exactly what he is doing, when the truth is he is clueless.
If you have an ice maker or other plumbing going to your refrigerator, every six months or so pull the refrigerator away from the wall and inspect this plumbing. There should be no condensation or corrosion on these plumbing lines, if there is, contact a plumber and have them look at it.
Be sure to have a running toilet fixed as soon as you can. Having a running toilet uses more water, which raises your water bill. To fix it yourself, you just have to find out what the problem is and buy the supplies you need. If you can’t fix it yourself, call a plumber.
Sometimes in the case of minor and or major emergencies we all have to become Mr. Fix it ourselves. If you’ve got blockage in your drains the first step is to try a commercial de-clogger like Drano. Simply pour it down the drain, wait ten minutes, and presto, your drain should be clear.
It is a general rule of thumb that you should replace a water faucet every seven years, even if you do not see anything wrong with it. Some faucet problems are not visible to the naked eye, which is why it is so important for them to replaced every so often.
If you are going to update the plumbing in your house, one thing to consider is installing a new tank-less water heater. They are much smaller than traditional tank heaters, which is a space-saver. Tank-less water heaters are available in gas or electric, depending on what your house needs.
By knowing your plumbing and how it works, as was stated before, can save you a lot of time and money. There’s nothing worse than a plumbing accident to mess up your day. So, using the advice from this article, you can be sure to save yourself a big headache!
Fixing your own plumbing can be a difficult and intimidating thing to try. There are so many things to know, and it seems like it could be easy to accidentally break something and make the problem worse. However, taking care of common plumbing problems can be easy with the proper knowledge. Read on for some practical tips on solving and avoiding plumbing issues.
Rigid copper is used for main water lines in many homes. You cannot bend rigid copper, so joints and tees must be soldered on. When soldering, always apply flux (also called soldering paste) to both surfaces. Flux retards oxidation when the copper is heated. Always use lead-free or nearly lead-free solder when sweating a copper joint.
Make sure you know where your home's water shutoff is located. You never know when there might be an emergency involving a broken pipe or damaged connection that requires you to turn off the water right away. In addition, knowing where the shutoff is located is vital before you start any plumbing project, in case anything goes wrong.
If you have issues with the plumbing making a hammering sound when you turn it off, check your water pressure. Any time your water pressure is above 80 PSI, you will hear extra water noise. This can be easily solved by the installation of a pressure-reducing valve, which can be done by most homeowners.
Frozen and bursting pipes from harsh winter weather is a problem that no-one wants, so plan now to winterize your exterior faucets and pipes against freezing conditions. A simple way to accomplish this is to find the exterior water shut-off valve located inside your home (often located in the basement). Turn off the water valve to stop water flow, and then open up the outside faucets to drain out any water that has collected. Be sure to turn off the outside water faucets tightly after the water has drained out. Take in any hoses you may have outside so they don't crack from the cold weather.
Find a better way to discard of cooking oil instead of pouring it down the drain where it can easily clog your pipes. Keep a coffee can or other metal container handy to pour grease into after cooking. Place the can in the freezer to harden the grease and when it's full, discard it with the trash.
Try to avoid putting things like fat, oils and grease down the sink drain. When they cool, they'll harden and clog your drain. If the sink has a garbage disposal, it will also make the blades less efficient. You should dispose of all oils outside of the sink.
Do not overload your garbage disposal. If you need to dispose of large items, cut them up into smaller pieces. Also, do not put too much in at a time, put one or two items in and wait a few seconds to dispose of the rest. Overloading your disposal can cause the engine to overheat.
Many people deal with clogged toilets. However, if your toilet will not flush every time, the water rises to the top, and there is bubbling effect occasionally, this can be due to a much deeper blockage in the main pipe. The main pipe must then be cleaned in order for your toilet to work properly.
If you live in an area that sees routine freezing temperatures, make sure you do something to keep your pipes from becoming frozen as well. There are a wide variety of ways you can keep your pipes from freezing, which will help you avoid damage to your home and costly repairs.
Do not, under any circumstances, put lemons down your disposal. Although the lemon smell will give your disposal a great smell, its acid can corrode the metal parts in it. Instead, use products that are made specifically for this use. You can purchase these products at most hardware stores or wherever cleaning products are sold.
Do you have a frozen drainpipe? You can use a garden hose to thaw it out. First of all, remove the trap from the drainpipe and insert the hose until it will not go any further. While lifting up the other end of the hose, pour hot water down it. Keep pouring hot water down the hose until the drainpipe thaws. To save time with cleanup, keep a bucket underneath to catch the water that overflows.
Periodically, make sure that the sump pump in your house is working to full capacity. Pour a few gallons of water into the sump pit, and your pump should drain that water out with minimal issues. Checking that your devices are working throughout the year can pay large dividends in the event of a crisis.
To make sure there is no accident or sudden rush of water when you tackle a plumbing project, make sure you are ready for a cleanup. If you go into the work with a huge stack of towels and blankets ready to absorb water, the prospect of needing to actually do it will keep you alert enough to avoid triggering the accident in the first place.
The most important plumbing tip you need to know is -- how to turn off your home's main water supply. Once the water is shut off, you can investigate problems and figure out how to resolve them. Walk the family through the house and show them where all the water shut-off valves are, and how to use them.
If you own property where the temperature gets below freezing for an extended amount of time each year, you should make sure that pipes located in unheated areas, such as crawl spaces and garages, are insulated. Pipes that are exposed to the outside elements or those that are prone to freezing, should be protected by heat tape or thermostat-controlled heat cables to prevent them from freezing.
As you can see, solving plumbing problems isn't so hard when you know what you're doing, or if you have the right advice. When you are well-informed it can save you agreat deal of money. Make a note of what you've learned in this article and see how easy it is either to fix your own plumbing problems, or at the very least, ensure that you get a good service from a professional.
Plumbing problems? You're not alone. Despite how simple it is to solve most plumbing problems, many people do not know how to fix their own simple plumbing issues. If you're one of these people and would like to avoid paying for the service, read on to find out how to become a plumbing expert!
Solder with safety in mind. When you solder a copper pipe you want to direct the flame on the copper pipe. The flame of the torch has to be four inches away from the piping. The flame should be targeted directly at the point where the copper piping needs to be disconnected.
Group all of your plumbing repairs before scheduling a plumber to come out. Check all of your fixtures and faucets. If anything is dripping, running or clogged, make a list for the plumber. That way, when the plumber comes, they can do all of the jobs in one visit. This will cut down on charges.
Make sure that you disconnect all hoses outside your house when the fall season hits. This is important to reduce the chance of freezing, which can cause damage to the connecting pipes. Disconnect all of your water hoses and store them safely to put your family in the best position for the fall.
Drain the sediment from the bottom of your hot water heater twice a year to keep the hot water heater working at its optimal levels. Simply open the drain valve and allow the water to run out into a bucket until the water runs clear. Then close the drain valve.
Always keep your garbage disposal clean. You can do this in many ways. Pour some dish soap in and let the disposal run for a few minutes with some cold water. Be sure to run it regularly, if not, it can cause rust. To eliminate foul odors, grind lemon or other citrus peels. You can clean the walls of the disposal by grinding small fruit pits or egg shells.
One way to prevent pipes from freezing during the winter is to keep cabinet doors in your house that contain the pipes open. This can insure that they get adequate heat to keep warm. Make sure also, to unhook and kind of hose outside and run a little water to clear the pipes of any remaining water going outside.
If you have drains in your house that have not been used for a long period of time, pour one gallon of water through them to keep them functional. Furthermore, this will have the added benefit of reducing any odors from entering your house from lack of use during the year.
Try to limit the amount of hair that goes down your drains. Hair can become tangled up in the pipe and end up blocking up the them, preventing water from flowing smoothly. Buy a cheap screened drain cover to put over your drain to stop any hair from going down and clean it off regularly.
Work with plumbers that offer flat rates. When a plumber is charging by the hour, they do not have an incentive to get the job done quickly. It is human nature to go just a little bit slower if it'll mean extra money in our pockets. If you cannot find someone who charges per project make sure that you are vigilant in watching the clock and their work.
Teach kids how to shut off the toilet's water supply. Kids are notorious for putting large wads of toilet paper and other things into the toilet, which inevitably leads to the toilet overflowing. Especially if your bathroom has carpet, show kids how to turn the water valve off if the toilet water keeps rising, to prevent the mess of an overflow.
When searching for a good plumber you should always check references. It is easy to just go with the lowest price, but you have to do your research and make sure the plumber has a good reputation with the people they have done work for in the past so you do not get a bad plumber.
Use a product like BioBen if you are planning to leave your system shut off for a few weeks. Water will still remain in the pipes and could start smelling because it is not moving. This type of product will keep the water from stagnating and from smelling too bad.
Governmental regulations sometimes prevent plumbers from actively providing maintenance to copper piping. If you have a calcium buildup in your copper piping, you are going to need to take care of this yourself. You have to get rid of all the water and add vinegar which eats away the calcium buildup out of copper pipes.
When installing a brand new water heater, if you see a pipe from the drainage pipe, reconnect it. This is probably what is called a recirculation pipe. This keeps the water in your home heated while reducing the amount of water wasted.
When it comes to plumbing, there is never an unsolvable problem. If you feel yourself becoming frustrated with the project, you should try to take a break from what you are working on. The greatest mistakes start to happen when you become angry and inpatient, so take a break and walk outside.
When facing temperatures below freezing in the winter it is important to leave the hot water dripping. This makes sure that the pipes don't freeze over and saves you the expensive repair of fixing and or entirely replacing a broken pipe. The slight cost of dripping hot water is well worth saving you from that large expense of replacing a broken pipe.
To prepare for the cold weather, properly drain all outside faucet bibs and turn off the water supply to those faucets. A piece of foam taped to the outside bib can provide excellent insulation to prevent any remaining water from freezing or splurge for a specialty cover that comes complete with velcro closures.
Plumbing problems aren't so tough to deal with when you have knowledge of how to fix basic plumbing problems. Next time you're thinking of calling an expensive plumber, pull up this article instead and see if you can fix the problem yourself with the tips you've read here today.
My name is Tom Roberts and on behalf of the Australian Building Codes Board, I'd like to welcome you to the update of the future of the Plumbing Code of Australia. Topics covered in this presentation include the history of the PCA, an overview of the regulatory framework surrounding the PCA, important information on how the NCC has changed, projects being conducted by the ABCB, intended for NCC 2019, key dates for the NCC development cycle, and how to register for the NCC. So where does the Plumbing Code of Australia or PCA sit within the regulatory framework? When you look at planning nationally, you can see the PCA and the rest of the national construction code is called up by state and territory legislation. The ABCB works within this area. Technical reference documents such as Australian standards are called up in the PCA. The PCA sets out the role of standards it calls up, and which parts and editions should be used. Administrative matters such as licensing approvals are retained in the regulations and not part of the NCC. The national construction code consists of the Building Code of Australia or BCA, which is the NCC Volume 1 for Class 2 to Class 9 buildings, and NCC, Volume 2 for Class 1 and 10 buildings. The Plumbing Code of Australia, NCC Volume 3 is for all classes of buildings. Historically, the regulation of plumbing and drainage in Australia has developed in close alignment with state and territory water and sewage authorities as they are regulated for sanitary drainage and water supply. The National Planning Regulators Forum or NPRF was established in 2002 with representatives from states and territories to develop the Plumbing Code of Australia. The PCA 2004 was published, however, only adopted by Queensland, South Australia, Tasmania, Victoria, and the ACT. In 2010, the PCA was reviewed as part of initiatives to incorporate all on-site construction requirements into a single code. The PCA 2011 was released as Volume 3 of the NCC by the ABCB. From 2011 to 2016, there was an annual change to the PCA, however, from 2016 onwards, the NCC has moved to a three year amendment cycle to provide greater stability for industry. During the lead up to NCC 2019, the ABCB has been able to focus on a number of projects to improve the PCA. The 2016 edition was the first NCC edition to be freely available online. So what's been done by the ABCB while not publishing its annual amendments to the PCA? The main projects include the development of acceptable plumbing practices, plumbing research in four main areas: backflow prevention, rainwater harvesting and use, fixed unit ratings, and warm water systems. The harmonization of the PCA and the BCA, the development of Australian Standards are another of other ABCB projects. I mentioned before acceptable plumbing practices, or APP, but what is it? An APP is an optional means of compliance with the performance requirements of the PCA. Similar to the structure of Volume 2 of the BCA, which contains acceptable construction practices, an APP would provide a simple solution, veneer single, detached slab on-ground Class 1 or Class 10 buildings. This will give practitioners the option of using reference documents such as ANZ/AS 3500 or the APP for these simple building types. The content of an APP will be developed based on the content of the New Zealand building code where it is also used as a compliance option. How would an APP fit into the regulatory framework of the PCA? As you can see on the slide, there's still an option of undertaking the performance or Deemed-to-Satisfy solution to meet the performance requirements of the PCA. Reference documents such as AS/NZS 3500 will remain the primary means of compliance for Deemed-to-Satisfy solutions and will still apply to all classes of buildings. However, for new single, detached slab on-ground Class 1 or Class 10 buildings, the APP will also be an option freely available and contained within the PCA. The Plumbing Code of Australia Research and development project was commenced in four areas of plumbing and drainage which were identified requiring exploration. These four areas include: backflow prevention, rainwater harvesting use, warm water systems and fixed unit ratings. Backflow prevention research has resulted in a report based on the desktop survey and preliminary targeted consultation which was released in 2015 for public consultation. Some of the key findings of the report discussed errors such as registration and testing which were considered to be not consistently enforced. That cross connections generally occur in individual and or agricultural situations and are also under reported. There was no evidence of widespread failures with general causes of being lack of awareness, poor design or mistakes. The only consequences, not the probability or likelihood, is considered in the risk assessment. Regulatory reliance on informative Appendix G of AS/NZS 3500 Part 1. The application to non-drinking water installations is unclear. Containment protection, application and responsibilities are unclear. The report contained recommendations for further work which the ABCB Board endorsed for the ABCB offers to progress. These consisted of containment protection outlined by both the network utility operators and within the PCA with greater engagement to aid the consistency. The development of cross connections control manual clarified above-ground rainwater tanks as low hazard. Probability in consequence risk methodology, a Deemed-to-Satisfy version of Appendix G to be developed and to be contained within the PCA. Clarification of backflow prevention requirements for non-drinking water supplies. Development of Deemed-to-Satisfy for access and maintenance solutions. Consolidation of NUA containment provisions within the PCA. Rainwater harvesting and reuse has resulted in a report which explored regulations, standards and guidance material and similar to the backflow prevention report, consisted of targeted consultation. The report was released in 2015 for public consultation. The key funding to the research confirmed national inconsistency. The recommendation of the report were endorsed by the ABCB Board for the offers to progress. These recommendations included increased engagement with affected industry stakeholders to promote national consistency. To recognize rainwater harvesting in the PCA for a new part. Clarify the application of the PCA with relation to rain water in other parts. Clarify the status of rainwater tanks used for bush fire control. Develop a non-mandatory handbook for the National use and current regulatory controls identified. Research on warm water systems has intentionally been selected as there is currently no prescriptive solutions in the PCA for these systems. The research resulted in a report outlining literature on design installation and maintenance of warm water systems. The development of a Deemed-to-Satisfy solution for warm water systems was not progressed due to the site specific nature of the systems, and the multiple means of Legionella and scolding risk mitigation strategies. The report was released for public consultation in 2015 and was updated based on the comments received through public consultation. The report has since been reformatted into a draft ABCB handbook and a peer review is currently being undertaken by consultants to ensure the information provided within the handbook is technically accurate and complete. Once reviewed and endorsed by the ABCB Board, the handbook will be made publicly available to provide guidance to practitioners. The final research project relates to a fixed unit ratings. This project was selected as current methods for pipe size and calculations are based on almost 80-year-old methods developed in the USA. Research resulted in a discussion paper being developed by consultants and was released by the ABCB in 2015. The paper explored the origins of current fixed unit ratings, basis and value of overseas equivalents, and comparisons with the Australian context. And the overview of the system design methodology using current fixed ratings. Numerous comments were received on this paper which is available on the ABCB website. ABCB will look further into this research throughout 2017 with a project plan currently under development based on the recommendations received through public consultation and the consultants. Another important project being undertaken by the ABCB is the harmonization of the building and plumbing codes which make up the NCC. There are a number of specific areas being investigated, some minor in nature and some are quite complex. These issues include areas such as: boilers and pressure vessels, swimming and spa pool plant and drainage, undue noise, stormwater, firefighting water services, heating ventilation and air conditioning provisions. Another area for the ABCB has a large amount of involvement with the development of the PCA reference documents. The ABCB is the link between the Plumbing Code Committee and the Committees of reference documents such as the Australian Standards WS14 committee. This involves keeping the plumbing code committee informed and consulted on, and it allows input at key stages during the development of the process. The role of the ABCB is also to assist the committees with compliance with the ABCB protocol for the development of NCC reference documents. The protocol ensures that the documents are prepared or revised are appropriate for a regulatory use, undergo consistent and transparent process, and are delivered in a suitable format and drafting style. There are a number of projects being undertaken by the ABCB which have an effect on the 2019 edition of the PCA. These include the NCC readability. This involves repackaging of the NCC to simplify its use and therefore make it more accessible to a wider audience that are exposed to the NCC as a result of making it freely available online. The initiative will initially relate to the NCC language and to a lesser extent, the NCC format. NCC digitization improvement look to enhance practitioner access in understanding of the NCC for a range of new and refreshed technologies The ongoing consolidation of state and territory plumbing regulations into the PCA, ongoing work to reduce state and territory variations to the PCA. So how does changes occur to the NCC? Changes to the NCC can be the result of a number of things such as government policy decisions, ABCB Project Work, proposals for change, or a change to a reference document. Those seeking to propose a change are required to submit justification to support the proposal. This justification should be proportionate to the size of the proposed change or its potential impacts. Justification should include a description of the proposal, an explanation of the problem it is designed to resolve. Evidence of the existence of the problem. How the proposal is expected to solve the problem. What alternatives to regulation have been considered? And why were they not preferred? Who will be affected and how will they be affected? And any consultation that has been taken. Any proposed changes to the PCA are considered by the plumbing code committee and for the BCA, the building codes committee. Proposed changes to the NCC are released for public consultation, and after comments are considered, changes are finalized and submitted to the ABCB Board for their final consideration and endorsement. NCC development dates. The Building Ministers Forum, or BMF, made the decision to move to a three-year amendment cycle following the 2016 edition to allow the ABCB to make the most of an effective use of resources, reduce unnecessary churn and focus on priorities. This means that the next scheduled update to the NCC will be in 2019. The key dates in the development of NCC 2019 are: the 1st September 2017 when the proposal for change submission process closes. The 2019 public comment draft will be available between the 1st February and the 13th of April in 2018. And the 2019 NCC will be available online in February 2019, and will be adopted by states and territories on the 1st May in 2019. How do you register for the NCC? The registration is a simple process. Firstly, log on to the ABCB website at abcb. Gov. Au and click the registration button on the top right of the homepage. You will then be asked to enter contact information and create a password. You'll also be asked if you wish to be updated on important information on NCC related materials, news events by email. Then click Register and you'll gain access to the NCC and other ABCB resources. So why register for the NCC? Other than to gain access to the NCC and other ABCB resources, free online registered users who have opted to receive communications will be advised when the public comment draft is available. You will also be alerted to when the ABCB is undertaking consultation activities such as part of regulatory impact analysis processes, or consideration of alternatives to regulation such as education and awareness-raising activities. Changes to the PCA affect all of the plumbing industry so more registrations are needed to keep industry informed of the work being done by the ABCB. Thank you for viewing the update on the future of the Plumbing Code of Australia.
Think Home Service Does best plumbing contractors nearby