Home

When you think of plumbing, do you just see it as a hidden and mysterious network of pipes and pumps that makes your toilets and sinks work? If so, then you are very unlikely to have a go at mauntaining or repairing the system. Plumbing is not actually that complicated, and there are many things that you can do yourself to maintain and repair your system. Read on to find out how.

Toilet Plumbing Problems

On very cold winter nights, allow your faucets to trickle slightly, especially if your pipes are located in a crawlspace. The running water prevents the pipes from freezing as quickly as they would otherwise. You can catch the water and use it for other household needs to prevent wasting it.

Check how well your toilets are flushing. If the handle needs to be played with in order to keep the water from running constantly, or if it needs to be held down several times in order to flush, you may need to switch out some of the parts in your tank. This is not expensive, and it could help reduce your monthly water bill. It could also mean that you avoid the embarrassment of the flushing system breaking when you have visitors!

Toilet Plumbing Problems

Find a better way to discard of cooking oil instead of pouring it down the drain where it can easily clog your pipes. Keep a coffee can or other metal container handy to pour grease into after cooking. Place the can in the freezer to harden the grease and when it’s full, discard it with the trash.

Use strainers in all drains to catch hair and other objects. This will prevent all the material from going down the drain and causing a clog, which can cause a bigger problem down the line. Clean out the strainers daily so that you don’t start getting backup of water in your sink or tub.

Toilet Plumbing Problems

Make sure that you disconnect all hoses outside your house when the fall season hits. This is important to reduce the chance of freezing, which can cause damage to the connecting pipes. Disconnect all of your water hoses and store them safely to put your family in the best position for the fall.

If your drain in any device is taking longer to drain water, then you may need to have your pipes professionally cleaned depending on the severity of the circumstances. Before you do this, there are several different products you can try. However, some of them are professional strength and all products should be used with caution.

Make sure you get a good recommendation or check the references before you hire a plumber. With good recommendations, it will assure that you are hiring an experienced plumber. If the experienced plumber is professional, he will have a fully stocked truck and be able to complete most small jobs in one visit.

Fitting Of Taps

If you live in an area that sees routine freezing temperatures, make sure you do something to keep your pipes from becoming frozen as well. There are a wide variety of ways you can keep your pipes from freezing, which will help you avoid damage to your home and costly repairs.

Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there’s a place to recycle it near your home.

If the hot water heater in your house is over ten years old, you should look at replacing it. Hot water heaters are very susceptible to corrosion on the bottom. This can lead to leaking and flooding whatever room it is in. Then not only will you have to replace it, but you’ll have to fix any damage caused by the leak.

When you’re going away on a vacation, you should consider shutting off the water supply to your home. This can help stop many problems before they start. If you don’t do this, you should have someone stop by your house regularly to check that nothing has gone wrong and that your home isn’t flooded.

Residential Plumbing Repair

Realize that branch lines can get blocked and cause sewage backups that affect main lines. If you can’t clear the blockage yourself, contact a professional plumber, who can insert a snake into the line to break up the blockage.

Do not pour grease and oil down your drains. Cooking grease will build up in your pipes and could cause back-ups. Keep grease and oil in a container in your fridge and throw it in the trash when it is full. Avoid clogging your pipes with any products containing oil or grease.

If you are seeing areas in your ceiling or walls that appear to have water damage or are sagging, make sure you turn off the power before inspecting. Electricity and water do not mix. The last thing you need is to go into the attic and get shocked by a pool of water.

To avoid plumbing disasters in your kitchen, never place hard-to-grind, stringy, fibrous waste, such as poultry skins, banana peels, carrots, celery, or cantaloupe pulp, into the garbage disposer. The disposer can’t sufficiently grind these food products and they will clog your sink drain. You should also run cold water down the drain for about 15 seconds before and after using the garbage disposer to flush the waste down the main drain.

Toilet Plumbing Problems

When it comes to plumbing a great choice is to invest in brass fittings. Sure, they may be more expensive upfront, however their longevity is amazing compared to the alternatives, so you end up saving money. As an added bonus, the brass fittings look so much better than the other alternatives.

It should not be necessary to call out a professional for every repair job. If you take your time and apply sensible advice, such as what you read here, you can successfully repair many of the common faults that develop. It may take a longer the first few times, but after a few successes you will pick up speed.

Tips And Tricks On How To Do Plumbing Right

24 Hour Plumbing Repair Ensuring that your home's plumbing is working properly is an important element of owning a home. Sometimes, you will need to pay special attention to your plumbing but it isn't always necessary to call a plumber. The tips provided below will teach you some great ways in which you can easily handle issues with the plumbing in your home. Solder with safety in mind. When you solder a copper pipe you want to direct the flame on the copper pipe. The flame of the torch has to be four inches away from the piping. The flame should be targeted directly at the point where the copper piping needs to be disconnected. Do not use the liquid cleaning supplies that are designed to clear clogs. These cleaners are harmful and can damage your pipes as they clear the clog. Instead of using damaging liquids, use a plunger or a plumbing snake. These are much more effective and will not harm pipes. Do not put cooking oils, fat, or grease, down your drain. These fats cause clogs by solidifying in pipes. To properly dispose of fats, put them in a bowl with a lid that you can dispose of. Once it gets hard, throw it in the trash or compost bin. If you operate the disposal on your sink, run plenty of cool water. Cold water helps to maintain the sharpness of the blades and makes the disposal run more smoothly. Hot water can clog your drain by allowing liquid grease to build up in it. Sometimes you have to make the choice between replacing or repairing. If you have an old appliance, that uses a lot of water or electricity, it may be best to replace. Sure, it will cost more initially, but it will save you money in the long run. The other thing is, you can't be sure how well a repair will work out, whereas with a new appliance you'll at least get a guarantee. Your water heater works more during the fall and winter so make sure that you eliminate all sediment buildup around this piece of equipment. Flushing this device can lead to increased longevity so that you do not face plumbing problems during the winter. This precaution will save time, money and effort. Prevention is the key to keeping your plumbing repair bills down. Drain clogs are probably the most frequent issue you will run into with your plumbing. Drains easily get clogged by hair. Putting a strainer on your drain can solve this problem. It is much easier to remove the hair from a screen than it is to get it out of a pipe. Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there's a place to recycle it near your home. Try to limit the amount of hair that goes down your drains. Hair can become tangled up in the pipe and end up blocking up the them, preventing water from flowing smoothly. Buy a cheap screened drain cover to put over your drain to stop any hair from going down and clean it off regularly. One way to avoid a common plumbing problem is to make sure never to flush anything but human waste and toilet paper down a toilet. Other things made of paper like tissues, paper towels, and the like do not dissolve the same way toilet paper does and can get stuck. When you're going away on a vacation, you should consider shutting off the water supply to your home. This can help stop many problems before they start. If you don't do this, you should have someone stop by your house regularly to check that nothing has gone wrong and that your home isn't flooded. To protect your money from unsavory plumbers, always get a written estimate before paying a cent or committing to a project. Good businessmen know to under-promise and over-deliver to savvy customers. Once a stated number is given, it is highly unlikely that your plumber will exceed the projected costs of the project. Every now and then, you should pour a large bucket of water down your basement floor drain. This will help to keep the trap seal full and prevent certain gases from coming up into your home. Also, be sure that you have your floor drain checked by a professional every few years. If the water is not going into your dishwasher, the first thing you should do is shit off the water under the sink. Chances are that you have some kind of blockage, and keeping the water turned on could actually create a bigger problem. To fix the blockage, you may need to call a plumber. If the water pressure on your street exceeds 60 pounds, you many want to consider installing a pressure reducing valve. Too much water pressure is actually harmful to your plumbing system and could cause excess water pressure. A pressure reducing valve cuts down your water pressure by almost 50 percent. The water heater in your home needs to have regular flushing to its plumbing in order to work properly. There is usually a valve at the bottom of the water heater that a hose can be attached to. Connect a hose to this valve and open it up all the way to flush scale and deposits out of the system. It is a general rule of thumb that you should replace a water faucet every seven years, even if you do not see anything wrong with it. Some faucet problems are not visible to the naked eye, which is why it is so important for them to replaced every so often. As indicated by this article, there are many ways to maintain and repair your plumbing system. Using this advice for your plumbing needs saves you the money you would spend on a plumber.

Excellent Plumbing Solutions That Anyone Can Do

Repair Pipe In this video we will show the basic steps to perform an underfloor heating calculation in DDS-CAD. We will start by changing the default floor type to a specific underfloor heating floor. To do so, open the storey function in the tool bar. Double click on the building entry to access the properties of the complete storey. Open the floor's properties by double clicking on it. Next, open the product database for floors. On the left side, select the underfloor heating category and select the appropriate floor type. Press ok again. Press yes to assign the new floor type to the complete storey. Click ok twice to close all dialogs. The next step is defining the heating facilities of the building and do a heat load calculation. Start by opening the building dialog from the tool bar. Next, select the tab heating facilities. In this case, we will set the building's heating source completely to underfloor heating. This means setting the radiators target output to zero and assign 100% to underfloor heating. By pressing the button set building and yes, the new settings will be applied to your complete building model. To complete, press apply. Now, let's move on to the heat load tab. Since we have changed the floor type and the heating facilities, we need to perform a heat load calculation. It is important that the heat load is recalculated when a change is made to the building model or system settings. After the calculation is completed, press apply to assign the calculation results to the model. Refreshing the model will update the part texts inside each of the rooms, automatically reflecting the calculated heat load. We are now ready to define the underfloor heating circuits and do a calculation. To do so, open the building dialog. Select the tab underfloor heating. Open the product database to select a suitable system. Select one of the the underfloor heating system types and press ok. By clicking yes, the selected system will be assigned to all rooms. The next step is selecting a manifold, to do so press new. Important is that we select a manifold from the underfloor heating filter. In this case we select a manifold from the flush mounted sub filter. Press ok again to position the manifold in the toilet's shaft. After we have positioned the manifold in the model, press Esc to open the underfloor heating dialog again. Next, press the draw button to define the underfloor heating circuits. The easiest way is to define an area across the complete model. Simply start in the lower right corner by clicking left mouse. Then make a diagonal line to the top left corner and press Enter. Press Esc to go back to the underfloor heating dialog again. Under options, we can set specific details for the calculation parameters. Before we start the calculation, we will first show how to modify the current heating surfaces. Start by pressing the cut out button. Move the cursor to the midpoint of the wall and make a diagonal line to the top left corner in the room. By pressing Enter we will cut out a part of the heating surface. Let's activate the ortho mode and cut out the bath tub surface as well. Contour the bath tub and press Enter to cut out the surface. Now, press Esc to go back to the dialog. Heating surfaces can be split in separate areas either by calculation or manually. To do it manually, click on the split into button and press left click inside the living room area. In the underfloor heating circuits table a list of all circuits is available. As we can see, we have now selected the heating surface that is located at the bottom of the living room Double click it to open its properties. Since this is a surface near the outside walls, we want to treat it as a high temperature zone. To perform the underfloor heating calculation, press calculate. In the lower right corner of the screen we see that DDS-CAD has identified 2 new issues, we will take a closer look at them later. Let's first check the heating circuit in the guest room. As we can see, the calculated actual output of the heating surface is 660 W. Click ok to close the dialog. The calculation results can also be presented in reports, to do so press the reports button. Select the calculation underfloor heating template, by double clicking it. In the lower left corner we have various report templates available. In this case, we will select the underfloor heating roomlist template. Click on the arrow to the right to go to the next page. Let's now look into the issues that were identified by DDS-CAD after performing the calculation. To do so, click on see more. The first issue is regarding the guest room for which the actual output is currently lower than the calculated target. The second issue indicates the same, but this time for the toilet room. In these cases we can decide to, for example, add additional radiators to reach the calculated target output. To conclude, we will generate a parts list of all underfloor heating materials. To do so, select the parts list function on the tool bar. A preview of all materials is shown in the table. Press the reports button to produce a parts list using one of the available report templates. At the top left, select the option parts list. Uncheck the cover page and select the parts list per room template. Here we now have a complete list of all underfloor heating materials per room.